541347
15
Zoom out
Zoom in
Previous page
1/28
Next page
WZ16:2DX
AND
WZ12:2DX U
SER
G
UIDE
15
M
ONO
I
NPUT
C
HANNEL
PAD
- Attenuates the input signal by 30dB. Affects both the XLR and jack inputs. Press this
switch when the input signal is too high even with the GAIN control backed off.
GAIN
- Use this control with the PAD switch to adjust the channel input sensitivity to match the
connected source (-60 to +10dBu) to the console operating level (0dBu). Use the PFL function to
check that the signal reads an average ‘0’ on the meters.
100Hz LO-CUT FILTER
- Attenuates frequencies below 100Hz to reduce low frequency source
noise such as microphone proximity popping, stage noise and transport rumble. Can be used to
clean up sounds that do not have much bass content such as vocals.
EQUALISER
- This provides separate, simultaneous control of 4 frequency bands. Each band
may be boosted or cut by up to +/- 15dB. The centre flat position is detented for quick resetting.
The
HF and LF
bands have a shelving response which means that all frequencies beyond the
turning point frequency are affected, HF = 12kHz, LF = 60Hz. Use HF to add sparkle or to reduce
source hiss. Use LF to add punch to the bass instruments. Used with the LO-CUT filter you can
tailor the low frequency response exactly as you require.
The two
mid frequency
bands have a peak/dip (bell shaped) response which means that the
maximum boost or cut occurs at the selected (centre) frequency. The centre frequency can be
swept over a wide range using the SWEEP controls. MF1 = 500Hz to 15kHz, MF2 = 35Hz to 1kHz.
Use the mids to add warmth or presence to the sound or to notch out problem resonances that can
result in feedback.
AUXILLIARY SENDS
- You can set up to 6 separately balanced mixes using the aux send
controls. Up to +6dB of boost is available.
Aux 1 and 2
are set pre-fader for
monitor sends
such as stage monitors, backstage, orchestra pit,
and musicians recording cue. The amount of channel signal in the monitor mix is independent of
the fader level. Pre-fade sends are post-EQ, post-ON as standard (can be reconfigured pre-EQ or
pre-ON by setting internal links).
Aux 3 and 4
are switched pre or post fader for more monitors, effects or separately balanced feeds
for
recording and broadcast
.
Aux 5 and 6
are set post-fader for sends to external
effects
devices such as reverb and delay. The
amount of signal sent to the effects device follows the fader level and ON switch. The processed
(“wet”) signal returned to the mix through the aux return inputs is therefore in proportion to the direct
(“dry”) signal from the fader to the mix.
PAN
- Positions the channel signal between L and R in the stereo mix. The centre position (mono
image) is detented for quick resetting.
ON
- This turns the channel signal on or off.
PEAK
- The red LED lights when the signal is within 5dB of clipping. Should this occur turn back
the GAIN control to reduce the signal level.
PFL
- Press PFL to listen to the pre-fade signal on headphones or local monitor without affecting
the main outputs. The signal level is shown on the L and R bar meters. The PEAK LED half lights
to show which channel PFL has been selected.
20
30
10
10
OO
PAD
20- 10
30
60
40
-30dB
PAD
GA I N
30
50
180Hz
MF1
MF2
60Hz
LF
-15
-15
45
35Hz
60
-15
HF
1k
500Hz
700
12kHz
-15
0
+15
0
+15
0
1kHz
300
+15
0
3kHz
7k
5k
15kHz
+15
100Hz
AUX
OO
6
AUX
OO
5
OO
OO
4
AUX
OO
3
AUX
OO
2
AUX
1
AUX
0
+6
0
+6
+6
POST
PRE
0
0
+6
+6
0
+6
PEAK
L
!
ON
R
PAN
PRE
POST
C
5
0
PFL
0
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath WZ12 mixwizard at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath WZ12 mixwizard in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Allen-Heath WZ12 mixwizard

Allen-Heath WZ12 mixwizard User Manual - German - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info