541379

Allen-Heath MixWizard WZ4-16 Manual

26
Zoom out
Zoom in
Previous page
1/32
Next page
Allen & Heath 26 WZ
4
16:2 and 12:2 User Guide
The MixWizard has a versatile architecture which should satisfy most applica-
tions you may encounter without modification. However, the following inter-
nal options provide alternative settings for those applications that may de-
mand them. Access is required to the internal assemblies. pluggable jumper
links are used in most places and also some links require cutting and soldering
a solder bridge.
Remove the base
Start by removing the side trims if fitted using a
Pozi crosshead screwdriver. Release the two M4 Pozi head pod securing
screws and rotate the connector pod to gain access to the three M3 rear
base fixing screws. Use a Torx starhead screwdriver to remove these. Ro-
tate the pod again to remove the four M3 underside base screws using the
Torx driver. Carefully lift off the base.
Configure the internal options
Jumper Options:
Fit the options required. Set the option jumpers to the required positions.
Make sure they are pressed fully home. Check that all channels are correctly
set and all options fitted according to their instructions. Make sure that no
debris or parts are left loose inside the console.
Solder Options:
Solder options require some ability with a soldering iron, if you have any res-
ervations then please contact your local service centre to carry out this pro-
cedure for you.
See page opposite for details on how to modify the solder options.
Refit the base
Carefully reposition the base. Refit the fixing screws.
Lock the connector pod in the required position using the securing screws.
Refit the side trims if required.
IMPORTANT:
Check carefully that all channel options are correctly
set as required. Errors on one or more channels now may cause user prob-
lems later. We recommend that you write the repositioned option settings
on a label and adhere this to the rear panel. This would provide a helpful
reference to other users of the console.
REMOVE SIDE TRIMS
REMOVE M4 POZI SCREW PER SIDE
ROTATE POD
REMOVE 4x M3 TORX SCREWS
REMOVE 4x M4 POZI SCREWS PER SIDE
REMOVE 3x M3 TORX SCREWS
ROTATE POD
LIFT OFF BASE
MONO INPUT STEREO INPUT (12:2)
AUX MASTER MASTER LR
AUX PRE/POST FADER
AUX PRE/POST FADER
AUX STEREO/MONO
AUX BALANCE OPTION
ST AUX STEREO/MONO
AB PRE/POST LR FADER
DIRECT OUT PRE/POST FADER
AUX PRE/POST INSERT/EQ
(SOLDER OPTION,
PCB UNDERSIDE)
User Options
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath MixWizard WZ4-16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath MixWizard WZ4-16 in the language / languages: English as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info