Manual Allen-Heath MixWizard WZ4-12 (page 11 of 32) (English)

541380

Zoom out

Zoom in

1/32

Allen & Heath 11 WZ

16:2 and 12:2 User Guide

The MixWizard uses professional grade 3 pin XLR and 1/4" TRS (3 pole) jack sockets. To ensure best perfor-

mance, we recommend that you use high quality audio cables and connectors, and take time to check for relia-

ble and accurate cable assembly. It is well known that most audio system problems are due to faulty or sub

standard interconnecting leads. The following mating plugs may be used to connect audio signals to the console:

Audio Connections

Avoid reversing + and - on balanced connections as this will result in reversed polarity (out of phase) signals

which may cause signal cancellation effects.

Where long cables runs are required, balanced interconnections should be used. However, line level intercon-

nections between more affordable 2-wire (signal, ground) unbalanced equipment and the console are unlikely to

cause problems if the cables are kept shorter than 10 meters or so. Refer to the wiring diagrams on the oppo-

site page.

Dealing with Ground Loops, Buzz and Interference

For optimum performance all audio signals should be referenced to a solid, noise-free ground (earth) point, fre-

quently referred to as the ‘star point’ or ‘clean earth’.

A ground loop is created when potential differences exist between grounds at different points in the system, and

the signal has more than one path to ground. In most cases ground loops do not result in audible problems.

Should you experience hum or buzz caused by a ground loop, check first that each piece of equipment has its

own separate path to ground. If so, operate ground lift switches on connected equipment in accordance with the

instruction manuals. Alternatively disconnect the cable screen at the destination end only. This breaks the of-

fending loop while keeping the signal shielding down the length of cable.

WARNING For operator safety do not remove the ground (earth) connection in the

power lead of the console or connected equipment.

To avoid interference pickup keep audio cables away from mains power units and cables, thyristor dimmer units,

computer equipment and mobile phones. Where this cannot be avoided, cross the cables at right angles to mini-

mise interference

A note about balanced connections

A differentially balanced connection has two signal wires, signal + (hot) and signal - (cold) and a shield. The signal

source generates positive going polarity down the + wire and negative polarity down the – wire. The destination

input stage accepts the + signal on its non-inverting (+) input pin, but it inverts the – signal, adding it to the +

signal. The result is that the wanted signal is boosted. Now examine what happens when unwanted interference

(hum and noise) is induced into the cable. The noise is induced equally and with the same polarity into both

wires. At the destination input the – wire signal gets inverted and added to the + signal. Because the polarity is

the same on both input wires the noise cancels itself out at this input. For this interference rejection to work it

is important that the source, the cable and the destination input are all balanced. Balancing provides greatest

advantage with low level signals such as those produced by microphones.

An impedance balanced output provides similar interference rejection, but without the signal drive on the - wire.

It does not generate a negative polarity signal at its – output. Instead, the – wire has no signal but is held at the

same impedance as the + wire. This means that both wires pick up the noise equally resulting in cancellation as

described above.

TRS jack plug

TS jack plug

XLR male plug

XLR female plug

RCA phono jacks

Tip

Sleeve

Ring

Tip

Sleeve

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath MixWizard WZ4-12 in the language / languages: English as an attachment in your email.

The manual is 5,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Allen-Heath MixWizard WZ4-12 Manual

Product: