541386
10
Zoom out
Zoom in
Previous page
1/12
Next page
iDR MixRack Getting Started Guide 10 AP7445 iss.3
Dual-Rack input expansion
Two MixRacks may be connected in Dual-Rack mode to expand the number of input channels from 64
to 128. The number of physical inputs available depends on which MixRacks are used.
Master
Slave
iLive Surface
ACE
Port B
NETWORK
ACE
ACE1
NETWORK ACE
CH1-64
CH65-128
Master
Slave
Port B
NETWORK
ACE
ACE1
ACE
Bridge
Step 1: Network settings
Note: Master and Slave MixRacks must have unique IP
addresses and Unit Names.
Make sure both addresses and names have been set
before the two MixRacks are connected together.
Set these in Network Settings
For example: 192.168.1.1 “Master 1-64”
192.168.1.4 “Slave 65-128”
Step 2: Connect Dual-Rack system
Connect the Surface to the Master MixRack using 1x
CAT5 cable in ACE Port A.
Link the Master and Slave MixRacks using 2x CAT5
cables. According to your preference, choose:
Method 1 – Connect a Master Network port to a Slave
Network port. Connect Master Port B ACE 1 to Slave
Port A ACE. or
Method 2 – Link a Master Network socket to its Port B
Bridge socket. Then use one cable to connect Master
Port B ACE 1 to Slave port A ACE.
Refer to Allen & Heath web site for recommended cable
type and maximum length.
Step 3: Set up Dual-Rack system
Using the Surface TouchScreen go to Utility / Network /
Dual MixRack Setup.
Touch Add Slave. Highlight a MixRack in the list to add
as Slave.
Touch Inspect. Details of the MixRack are displayed.
Check that the firmware is compatible.
Touch Apply to add the MixRack as a Slave. The
MixRack reboots and resets its parameters.
Note:
Channels 1-64 are sourced from the Master MixRack
(Preamps cannot be mapped across MixRacks).
Channels 65-128 are sourced from the Slave
MixRack.
Surface audio can only be assigned between
channels 1- 64 (connects to Master MixRack).
Each MixRack processes its own channels 1-64 or
65-128.
The Master MixRack processes the 32 buses.
FX may be inserted on Master channels 1-64 only.
Channels cannot be ganged across MixRacks.
The Reset Network Settings recessed switch
restores
default sin
g
le MixRack o
p
eration.
Including Surface audio
Method 1
Separate cables
for audio and
control
Method 2
Control bridged
over ACE for
single cable link
to the Slave.
iLive-R72
iLive-T80
iLive-T112
The ACE option
card must be
fitted to Master
MixRack Port B
If required Slave
Port B may be
used for audio
networking,
recording and
other more.
(control) (audio)
(control and audio)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath iDR-64 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath iDR-64 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info