541368

Allen-Heath GS-R24 Manual

11
Zoom out
Zoom in
Previous page
1/44
Next page
Allen & Heath 11 GS_R24 User Guide
MONO INPUT CHANNEL
Line Input Jack Socket
Standard 1/4” (6.25mm) Jack socket for balanced or unbalanced line
level signals. Wired Tip=Hot(+), Ring=cold (-), Sleeve=Chassis.
Insert Jack Socket
Standard 1/4” (6.25mm) Jack socket for unbalanced insert send and
return signals. Wired Tip=send, Ring=return, Sleeve=Chassis. Nomi-
nal level is 0dBu. The insert point is after the 100Hz filter and before
the EQ.
Gain Control
This adjusts the gain of the input amplifier to match the signal level
of the input. The gain is varied from +6dB to +60dB for signals
plugged in to the xlr socket (Mic Input) and –14dB to +40dB for
signals plugged into the Line input jack.
100Hz Hi-pass Filter
The Hi-pass filter is used for reducing pop noise and
rumble from microphone signals. It is a 2-pole (12dB
per octave) filter with a corner frequency set at just
below 100Hz.
The filter affects signals from both Mic XLR and Line
jack socket.
Line Input Switch
Selects the source for the pre-amp from XLR to Line input jack. The
balanced input signal is padded by 20dB but noise and distortion are
kept to a minimum in order to make it transparent when connecting
external devices.
Microphone Input Socket
Standard 3-Pin XLR socket wired as Pin 1=Chassis, Pin 2=hot (+),
Pin 3=Cold (-).
REAR PANEL CONNECTIONS
Direct Output Jack Socket
Standard 1/4” (6.25mm) Jack socket for Channel output signal.
Wired Tip=Hot(+), Ring=Cold(0V), Sleeve=Chassis. Nominal level is
0dBu. The source for the Direct Output is selectable by option
jumpers internally, factory set to Pre-Fade.
48V Phantom Power Switch
Applies +48V to pins 2 and 3 of the XLR input though 6k8 resistors
for phantom powered condenser microphones.
FRONT PANEL CONTROLS
Polarity (phase) reverse switch
Reverses the polarity of the balanced input signal phases for both
mic XLR and Line jack inputs.
10.00 Hz 100.00 1000.00 10000.00 40000.00
-40.00
-35.00
-30.00
-25.00
-20.00
-15.00
-10.00
-5.00
0.00
dBr
60 40-14 6
30
40
50
0
20
GAIN
HPF
100Hz
+48V
LINE
POL
DIRECT
OUT
INSERT
LINE
MIC
C
T
R
T
M1
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GS-R24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GS-R24 in the language / languages: English as an attachment in your email.

The manual is 8,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info