541348
15
Zoom out
Zoom in
Previous page
1/28
Next page
GL2200 USER GUIDE
15
STEREO RETURNS
Two stereo return inputs are provided with 2-band EQ, sends to auxes 1 & 2 and
routing to L-R mix or groups 1-2/3-4. These are normally used to return the effects
(‘wet’) signal, usually from a stereo device, to the mix. They can also be used for
additional line inputs to the mix.
A 2 band EQ provides HF and LF control with 15dB cut and boost at 12kHz and
80Hz respectively. This is often used to remove unwanted high or low frequency
noise from effects devices.
2 aux sends are provided to feed a summed left and right pre-fade post mute
signal to auxes 1 & 2. This is ideal for returning effects to the monitors without
using up valuable channel inputs.
The BAL control adjusts the balance between left and right signals, or can be used
as a pan control to route the signal to one side only by rotating fully.
MUTE switches the signal off when pressed regardless of fader position. Muted
Returns are indicated by red LEDs. Mute does affect the pre-fade aux sends.
Pressing PFL lets you listen to the channel pre-fader signal on headphones
without interrupting the main console outputs. The signal level is shown on the L-R
bargraph meters. In this way each sound can be correctly lined up and checked at
any time.
L-R/1-2 (3-4) ROUTING SWITCHES - In the up position the signal is routed to the
main L-R mix but may be returned to the corresponding pairs of subgroups for
group effects (1-2 or 3-4).
A smooth travel 60mm FADER provides precise control of the level.
AUX OUTPUTS
AUX MASTERS
Each aux mix has a master level control that adjusts the output level to match external
equipment, or to trim the monitor or effects level without affecting the mix balance. Up to +10dB
of boost is available above the nominal ‘0’ position. Auxiliary outputs are on 3-wire impedance
balanced 1/4” TRS jacks.
AFL (After Fade Listen) routes the post mix signal to the console meters and headphone
monitoring to allow checks for sound quality and mix level.
If MODE SWITCHING aux/groups reverse is in operation, aux master level controls are
connected to the corresponding group busses (Group 1 to Aux Master 1, etc...). Refer to
MODE SWITCHING section on page 17 for more information
+15-15
+15-15
0
1
AUX
+6OO
0
2
AUX
+6OO
0
ODD
LR
EVEN
BAL
MUTE
L-R
1-2
30
20
10
0
5
5
12kHz
HF
PFL
60Hz
LF
OO
10
RETURN
STEREO
1
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
AUX
OO+10
0
OO+10
0
OO+10
0
OO+10
0
OO+10
0
OO+10
0
AFL AFL AFL AFL AFL AFL
GRP/AUX 1-2
REVERSE
GRP/AUX 3-4
REVERSE
L-R/AUX 5-6
REVERSE
FOH
STAGE MONITOR
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GL2200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GL2200 in the language / languages: English as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info