541351
4
Zoom out
Zoom in
Previous page
1/20
Next page
4
GL3300 U
SER
G
UIDE
INSTALLING THE POWER SUPPLY UNIT
Refer to the SAFETY WARNING on the first page of this User Guide.
The RPS9 power supply unit conforms to safety standard EN 60065
AC mains supply = 100 to 110 V.AC 100 T 3.15A 20mm fuse
AC mains supply = 110 to 125 V.AC 120 T 3.15A 20mm fuse
AC mains supply = 210 to 230 V.AC 230 T 1A 20mm fuse
AC mains supply = 235 to 260 V.AC 240 T 1A 20mm fuse
Check that the voltage indicated in the fuseholder window is the
same as the mains supply in your area.
To avoid the risk of fire replace the fuse only with the correct
type and value as specified on the unit.
It is normal for the power unit to dissipate heat. Ensure adequate
ventilation around the unit. Do not cover the unit or position it on
soft furnishings during operation. Do not position other equipment
known to generate significant amounts of heat below the unit. It is
recommended that rack units containing high power amplifiers and
other heat dissipating equipment are fitted with cooling fans.
Always switch the power unit off before connecting or
disconnecting the console power cable.
This unit contains no user serviceable parts. Do not remove the
cover. Refer servicing to qualified service personnel only.
Note: The RPS9 is fitted with a rear panel ground lift switch. This is for use when the unit powers certain
other Allen & Heath equipment. This switch is not operative on the GL3300 range. Refer to the section
on 'EARTHING THE AUDIO SYSTEM'.
The RPS9 Power supply is provided with the GL3300 to convert the AC mains voltage to the regulated
positive and negative DC voltages required to power the console. It also supplies the +48V DC phantom
power voltage for use with certain microphones. It connects to the console by means of a 2.5 metre DC
power cable fitted with a locking 5 pin XLR plug. Mains input to the RPS9 is via a mains cable with
moulded plug suitable for the local supply. A standard 3 pin IEC connector plugs into the RPS9 mains in
socket with integral voltage selector and AC mains fuse.
The RPS9 may be operated free standing or 19" rack mounted (2U height) up to 2 metres away from the
console. As with any power supply unit it is recommended that it is positioned away from the console or
other signal processing equipment containing sensitive low level audio signals to avoid any possible hum
pickup.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GL 3300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GL 3300 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info