693707
47
Zoom out
Zoom in
Previous page
1/62
Next page
Applications
Multimix 12R Reference Manual 37
APPLICATIONS
Multitrack recording
See the "Connections" chapter for information on how to connect the
Multimix 12R to an ADAT or other multitrack recorder.
In the most common setup, the ADAT is patched into the INSERT
points of each channel. It receives signal directly from the [TRIM]
control; no other controls will affect the level being recorded to tape.
Tracking/Overdubbing
1. Put the desired tracks of the ADAT into record ready mode. Press
"Auto Input Monitor" or "All Input Monitor" depending on your
situation (see the ADAT manual for more information).
2. With the signal source (microphone or line input) active, slowly
increase the [TRIM] level of each input while watching the ADAT
meter until the top red segment comes on. Then turn down the
trim level so that the red LED does not light.
3. Set the EQ, aux, and channel faders for the desired control room
mix. Note that none of these settings will affect the signal going to
the ADAT.
4. For overdubbing, put the original tracks into safe mode. These
tracks will play back through the same channels they were
recorded on.
5. If necessary, repatch the microphone or line inputs to the next
channels you want to record. NOTE: the ADAT and ADAT-XT can
automatically "normal" the input to track 1 to any odd-numbered
track, and the input to track 2 to any even-numbered track. Check
the manual of the ADAT or XT for more information.
Applications
Mixdown
You may leave the ADAT connected to the INSERT jacks for mixdown;
there's no need to repatch to the LINE IN jacks.
Make the connections according to the procedure in the "Connections"
chapter.
1. Connect the MAIN OUTs (-10 dBV or +4 dBu, depending on the
deck) to the inputs of the mixdown deck.
2. Connect the outputs of the mixdown deck to the TAPE IN jacks.
3. Connect the [MONITOR OUT] jacks to the inputs of your control
room monitor amplifier.
4. Press the [PHONES/MONITOR] switch down so it is in the TAPE
position.
5. Put the mixdown deck into record/pause mode, play the ADAT,
and adjust the mix and level controls of the mixer for the desired
level. Set the MASTER fader up to the maximum, and adjust the
input controls of the mixdown deck until its meters give the desired
reading. You will also be able to see the levels on the mixer itself;
check to make sure the output of the mixdown deck is set to
nominal (unity gain).
By monitoring through the mixdown deck, you'll be able to hear if
there is any distortion in that deck's electronics.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alesis MultiMix 12R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alesis MultiMix 12R in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info