693707

Alesis MultiMix 12R Manual

35
Zoom out
Zoom in
Previous page
1/62
Next page
Operating Instructions
Multimix 12R Reference Manual 25
OPERATING
INSTRUCTIONS
Before turning the mixer on, "zero out'
the controls
To avoid surprises while you're setting up a new system, set all
controls to their "zeroed out" positions as follows before proceeding:
1. Make all connections to the Multimix 12R, as described in the
previous chapter.
2. Bring all channel faders and the [MASTER] fader down to
minimum.
3. Set all [TRIM] controls to minimum (full counterclockwise).
4. Set all [AUX 1], [AUX 2], STEREO AUX RETURN,
[PHONES/MONITOR] controls to minimum (full
counterclockwise).
5. Set all [HIGH] and [LOW] EQ, [PAN], and [BAL] controls to "12
o'clock".
Operating Instructions
Setting input trim levels
✪ Proper setting of the [TRIM] controls is crucial to low-noise, distortion-
free operation. If the trim is set too high, there will be distortion even
if the channel faders are low. If the trim is set too low and the channel
faders are raised to get the signal loud enough, you will be amplifying
the noise of the mixer.
Instead of doing this, get as much gain as possible as close to the signal
source as possible. If you've plugged a synthesizer or other line-level
source into the Multimix 12R, set its output volume to maximum. If a
microphone is the source, the Multimix 12R's [TRIM] control will
determine the gain of the system.
✪ The goal is to get the signal as loud as possible as early as possible
in the signal path, without causing clipping (distortion) anywhere in
the path or in the sound system.
PEAK LED method
Each channel of the Multimix 12R has its own [PEAK] indicator, which
will light when the signal level rises to within 6 dB of clipping. In
situations where the maximum signal-to-noise ratio is required (such
as digital recording), use the PEAK LED as a guide for setting the
[TRIM] control.
✪ When the PEAK LED is flashing, it does NOT necessarily mean that
distortion has occurred. There is usually some headroom left if the PEAK
LED is flashing momentarily on the loudest peaks.
1. With the sound source active, and the channel fader down to
minimum, raise the [TRIM] control until the PEAK LED flashes
occasionally on the loudest transients.
2. If desired, lower the [TRIM] control slightly until the flashing stops.
Note for extremely high level line inputs in stereo channels: If the
[TRIM] setting is set below unity (12 o'clock position) on a stereo
channel, it is possible for the first input stage to clip without the
PEAK LED coming on. If distortion is still heard after lowering the
trim to its minimum setting, it means the source is extremely high
(+22 dBu or higher). In this case you must lower the output level of
the source, use an external pad, or repatch to a LINE IN on
channels 1-8 (which can take up to +32 dBu levels before clipping).
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alesis MultiMix 12R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alesis MultiMix 12R in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info