693708

Alesis MultiMix 10 Wireless Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
5
*WARNING: If your unit has a voltage selector
switch, change its setting only when necessary
(e.g., when traveling to a country or region with
a different voltage). Selecting an improper
voltage setting can damage the unit.
**WARNING: Channels 1-4 each have mic
level and line level inputs. Attach either a
microphone or a 1/4” cable to the mic/line
channel, but do not attach both cables to the
same channel at any one time. In extreme
cases, doing so can damage your microphone.
1
2
3
4
5
6
8
8
12
13
14
10
11
16
17
18
19
20
15
7
8
7
1
2
3
4
5
6
7
8
9
10
10
13
13
13
13
12
12
12
12
11
11
11
8
7
8
7
7
7
8
7
8
9
Wireless
REAR PANEL
1. Power Cable Input (IEC) – Insert the included power
cable here.
2. Voltage Selector* – If your unit has a voltage selector
switch, change its setting only when necessary (e.g.,
when traveling to a country or region with a different
voltage). Selecting an improper voltage setting can
damage the unit.
3. Power ON/OFF Switch – Turns MultiMix 10 Wireless’s
power on or off.
4. Phantom Power Switch – Provides phantom power
(+48V) for condenser microphones. Phantom power is
applied to the XLR microphone inputs.
5. Antenna – Adjusts the reception of the signal that is being
received from a Bluetooth source such as a PC, Mac, iOS
device, Android®, etc.).
6. MAIN OUT – Use standard 1/4" TRS cables to connect
this output to the house speaker, recorder, or amplifier
system. Control the level of this output using the MASTER
fader.
7. MONITOR OUT – Use standard 1/4" TS cables to connect
this output to your monitor speaker or amplifier system.
Control the level of this output using the PHONES/MONITOR knob.
8. Aux Sends – Two mono 1/4" TRS auxiliary sends allow you to connect effects that can be blended in with the
source (or "dry") signals.
One typical example is to use one aux send for a reverb unit and the other for a
monitor mix for the musicians.
9. Stereo Aux Return – Connect the outputs of an external device to these inputs with 1/4" mono cables. This is
usually reserved for outboard effects devices but can also be used as an extra input channel for synthesizers,
drum machines, etc. If your source is mono, plug it into the left jack and it will be heard on both the left and right
sides.
10. Ext In (RCA) – These stereo RCA jacks accept consumer-level (-10dBv) inputs from sources such as tape
decks, CD players, and MP3 players. Only connect consumer-level equipment to these jacks. Professional-level
equipment operating at +4dBu will distort unless you significantly lower the volume on such equipment.
11. Stereo Line In – Connect line-level devices to these inputs with 1/4" cables.
12. Mic/Line In** – The first four channels of the mixer accept microphones via the XLR connectors or mono line-
level sources via the 1/4” connectors. Channels 9/10 can be used with the Ext In or with a paired Bluetooth
device.
13. Insert – 1/4” TRS jacks on channels 1-4 allow you to connect external processors (gates, compressors, pitch
correction devices, etc.) into the signal path of these channels. The insert signal is brought into the channel
directly after the preamplifier (controlled with the TRIM knob) and before the channel’s EQ and fader. The insert
jacks require use of an “insert” cable, which has a TRS (Tip-Ring-Sleeve) connector on one end for connection to
MultiMix 10 Wireless and two TS (Tip-Sleeve) connectors on the other end. Attach the “Send” connector to the
INPUT of your external processor. Then, attach the “Return” connector to the OUTPUT of your processor. See
the insert cable diagram under USING MULTIMIX 10 WIRELESS FOR MULTITRACK AUDIO RECORDING.
CONNECTING ELECTRIC GUITARS AND BASSES
Electric guitars and basses can be connected to the 1/4” line inputs as well. The combination of the Trim control and
the fader level on the front panel will deliver more than enough gain to drive these sources. However, note that the
line-level inputs are relatively low impedance, whereas most electric guitars and basses perform best when
connected to a high impedance input closer to 200k
Ohm or higher. The resulting impedance mismatch may dull the
sound of the guitar or bass. If this occurs, use a direct box to connect high-impedance instruments to MultiMix 10
Wireless.
Note: If you want to connect a standard
turntable to MultiMix 10 Wireless, use a
dedicated turntable-to-line-level preamplifier.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alesis MultiMix 10 Wireless at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alesis MultiMix 10 Wireless in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info