Manual Alecto WS-5300 (page 48 of 60) (English, German, Dutch, French)

708531

Zoom out

Zoom in

1/60

Weather station:

Slide the battery cover at the rear downward, replace the CR-2032 battery according to the markings inside

the battery compartment and slide the battery cover back onto the weather station. Connect the supplied

mains adaptor. The weather station will now start searching for the outdoor sensor for 1 minute. Therefore,

insert batteries into the outdoor sensor within that 1 minute.

Outdoor sensor:

Open the battery compartment by sliding the battery cover downward with a

small screwdriver. Insert 3 x size AA 1.5V batteries according to the gure below,

paying attention to the polarity (+ and -). Replace the cover (batteries are not

included).

2.2 Pairing the weather station / outdoor sensor:

Automatically:

As soon as the mains adaptor is connected to the weather station, the weather station starts searching for

a signal from the outdoor sensor for 1 minute. Therefore, if you insert the batteries into the outdoor sensor

within that minute and the units will ‘nd’ each other, they will be automatically paired and the display of the

weather station will show the temperature transmitted by the outdoor sensor.

Manually:

If the units cannot be paired automatically, or after replacing the batteries, you can pair the outdoor sensor

(again) with the weather station unit as follows:

1. press and hold the SCAN button on the weather station for 2 seconds until the antenna symbol starts

ashing in the display

2. Press briey press the RESET button on the outdoor sensor

3. the units will have found each other (again) after several seconds

2.3 Positioning:

Weather station:

You may choose to suspend the weather station from a wall using a simple screw or to use it

as a desk model using the supplied table stand. In any case, never place the weather station in

direct sunlight or nest to a heat-radiating lamp or stove.

Outdoor sensor:

You may choose to place the outdoor sensor on a at surface (e.g. a fence or railing) or onto

a pole (max. Ø 32.5mm (excluded)). In any case, make sure to position the unit at least 1.5

meters above the ground, standing freely in the rain and wind.

Outdoor sensor placement tips:

To have the rain and wind meter function as accurate as possible, the

outdoor sensor must be positioned exactly horizontal. To do so, use the

built-in spirit level on top of the outdoor sensor.

To be able to indicate from which direction the wind is

blowing, the outdoor sensor must face the North. See above

the designation N on the outside sensor. Use an accurate

compass (not included) to properly aim the unit.

Ensure that the distance between the outdoor sensor and

weather station is no more than 30 to 50 meters.

reset

>1,5m

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-5300 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 13,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alecto WS-5300 Manual

Product: