708530

Alecto WS-4900 Manual

62
Zoom out
Zoom in
Previous page
1/72
Next page
62
Automatic:
As soon as you install the batteries into the indoor unit, the clock starts searching for the DCF radio signal
to set the correct time and date while the antenna symbol ashes. After several seconds or minutes the
WS-4900 will start showing the correct time. In extreme cases, it can take over a day before the DCF time
is shown.
while searching for the radio signal, you cannot continuously switch on the display lighting. However
by pressing the ALARM/SNOOZE button, the display lighting will switch on but switches o again
after 5 seconds. As soon as the clock has found the radio signal, or when stopping the search by briey
pressing the RCC button, the display lighting switches on continuously.
Manually:
If the clock cannot receive the radio signal or cannot receive it well enough, you can set the clock manually
as follows:
1. Press and hold the button for 2 seconds, 12Hr or 24Hr will appear in the display
2. Use / to set the time format, then briey press the button
3. Use / to set the hours and then briey press the button
4. Use / to set the minutes and then briey press the button
5. Use / to set the seconds to 0 (this allows you to have the clock run synchronously with your own
clock) and then briey press the button
6. Use / to set the year and then briey press the button
7. Use / to set the month and then briey press the button
8. Use / to set the date and then briey press the button
9. Use / to set the dierence in hours as compared to the DCF time. For use in the Benelux, select ‘0’
and briey press the button
10. Use / to set the language for displaying the days, you may choose from: EN (English), FR (French),
DE (German), ES (Spanish) or IT (Italian), briey press the button
11. Use / to determine whether the clock must automatically switch to daylight saving time (AUTO) or this
must be done manually (OFF), briey press the button
The clock is now set manually.
When the DCF receiver is enabled and a strong signal is being received, the receiver will overwrite the
clock display.
To switch the DCF receiver on/o:
You may switch o the DCF receiver as follows to only display the time and date you’ve programmed
yourself:
• to switch o: press and hold the RCC button at the rear of the weather station for 8 seconds until OFF
illuminates and the antenna symbol disappears
You may switch the receiver back on as follows:
• to switch on: press and hold the RCC button at the rear of the weather station for 8 seconds until ON
illuminates, the antenna symbol starts ashing and the display turns green.
The symbol in the upper part and in the middle of the display shows the status of the DCF clock:
No symbol: the DCF receiver is switched o; the displayed time is determined by the internal
clock of the weather station
ashing: the DCF receiver is switched on and is searching for the DCF signal; the displayed
time is determined by the internal clock of the weather station
remains lit: the DCF receiver is switched on and is receiving the DCF signal; the displayed time
and date are determined by the atomic DCF clock in Frankfurt
3.5 To reset the rain data:
After everything is installed, press and hold the HISTORY button for 10 seconds to delete all measurement
data up to that moment. This prevents you from seeing measurement data at a later time that was caused
by movements during the installation.
… 62 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto WS-4900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-4900 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info