794960
5
Zoom out
Zoom in
Previous page
1/56
Next page
5
1. Open the battery compartment at
the back of the indoor unit.
2. 
all the way to the left.
3. Insert the second battery and
slide it again to the left.
4. Insert the third battery.
5. Finally, replace the battery cover.
Hang or stand:
The indoor unit can either be placed freestanding on a cabinet or desk (fold
out the stand on the back of the indoor unit for this purpose) or the unit can
be hung on the wall (see keyhole openings on the back).
4.2 Outdoor units:
General installation and placement tips:
First, check that the outdoor units are within reach of the indoor unit
before permanently mounting the outdoor units. Keep the distance
between the outdoor units and the indoor unit to within 30 meters.
Ensure that the outdoor units are placed at least 1,5 meters above the
ground and freely exposed to the rain and wind.
In order for the outdoor units to work as accurately as possible, they
must stand as horizontal as possible. For the outdoor rain unit, check
that the surface is level before mounting.
To indicate which direction the wind is coming from, the outdoor wind
unit must be oriented to the South. See the S designation at the
bottom of the outdoor unit for this. Use the compass on the outdoor
wind unit to correctly orientate the unit.
Make sure the outdoor units hang and/or stand freely. The wind speed
meter and the wind vane, in particular, should hang in direct wind.
AAA 1,5V AAA 1,5V AAA 1,5V
Find a location where the likelihood of blowing leaves is minimal.
󰀨
measurement results. In any event, we advise you to place the outdoor
units in such a way that it is fairly easy to remove any leaves and to
replace the batteries.
Perhaps the outdoor units can be located within reach for a week to try
out all functions. Check that everything is functioning properly before
placing the outdoor units in their permanent location.
4.3 Outdoor unit wind:
Registration:
First register the outdoor units with the indoor unit before permanent
placement of the outdoor units Once the indoor unit batteries are installed, it

After the 5 minutes, the indoor unit can be manually set to receive. To do
this, press the channel button for 2 seconds to set the indoor unit to
receive mode.
Insert 4 x 1,5V AA batteries in the outdoor wind unit. See diagram. Set the
Channel switch to the same channel selected on the indoor unit. Then press
the TX key. Check that the indoor unit has received the signal. Press the
TX button once more, if necessary. The outdoor temperature and humidity
are displayed on the indoor unit via the outdoor wind unit.
The outdoor wind unit is registered
when the information appears on
the display.
󰀨
reception, press the “WAVE” key.
To turn the DCF-77 reception on
again, register the outdoor unit

and reinserting the batteries
and repeating the registration
procedure.
S
AA 1,5V
AA 1,5V
AA 1,5V
AA
1V
A
AA 1,5V
TX
WAVE
1 2 3
TX
WAVE
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto WS-3850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-3850 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info