708517

Alecto WS-1050 Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
11
EN
ATTENTION: THE ILLUSTRATIONS THIS
USER’S MANUAL REFERS TO CAN BE
FOUND ON THE LAST PAGE OF THIS
MANUAL.
INSTALLATION
Power supply:
1. Slide down the battery cover at the rear
of the indoor unit and remove it.
2. Place 2 batteries, type AAA, 1.5Volt,
according to the markings inside the
battery compartment (see A). Batteries
are not included.
After you’ve installed the batteries, the indoor
unit will start scan of 3 minutes for any nearby
outdoor unit. That’s why you should follow the
instructions 4, 5 and 6 within those 3 minutes.
3. Unscrew the battery cover with a
crosshead screwdriver.
4. Place 2 batteries, type AAA, 1.5Volt,
according to the markings inside the
battery compartment (see B).
5. Set the channel switch to your desired
transmitting channel 1, 2 or 3.
Please select the same channel on the indoor
unit that you’ve set on the outdoor unit.
6. Press the “
WS-1050, Alecto color and graphics
page 2/4, indoor unit, screening
v1.1
MAX/MIN
CH
。
C
l
。
F
” channel button of the
indoor unit, placed above the battery
compartment. Each time you press this
button, the receiver will change to the
next channel.
The display will show which channel
number is selected.
To make the outdoor unit transmit again:
7. Press the “TX” button (see C) to have
the outdoor unit transmit again when the
registration has failed.
As soon as both the indoor and outdoor unit
have been found, the outdoor temperature
will appear on de display of the indoor unit
(see D).
8. Now replace the battery covers on the
indoor and outdoor unit.
9. Both units can be suspended from a
screw (see E) or placed on a surface
using the foldable table support (see F).
Temperature display setup:
The temperature unit can be expressed in
ºC or ºF. Press the “
WS-1050, Alecto color and graphics
page 2/4, indoor unit, screening
v1.1
MAX/MIN
CH
。
C
l
。
F
” button to switch
between ºC and ºF.
Maximum and minimum display:
De minimum temperature measured and the
maximum temperature measured can be
displayed.
• Briey press the “
WS-1050, Alecto color and graphics
page 2/4, indoor unit, screening
v1.1
MAX/MIN
CH
。
C
l
。
F
” button to show
the minimum temperature.
• Briey press the “
WS-1050, Alecto color and graphics
page 2/4, indoor unit, screening
v1.1
MAX/MIN
CH
。
C
l
。
F
” button again to
show the maximum temperature.
• Press and hold “
WS-1050, Alecto color and graphics
page 2/4, indoor unit, screening
v1.1
MAX/MIN
CH
。
C
l
。
F
” for two seconds
to reset the maximum and minimum
temperature.
Positioning tips:
• Never place the indoor unit in direct
sunlight and keep it away from heat
radiating objects (lights, heaters, etc.)
• Never place the indoor unit next to
large metal surfaces or heavy electrical
equipment, ensuring proper reception of
the radio controlled signals.
• The outdoor unit is not waterproof.
Always place this unit on a spot protected
against rain and wind.
• The distance between the indoor and
outdoor unit should be no more than
50 meters.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto WS-1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-1050 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info