Using: A smoke detector is in operation when the batteries are installed. Make sure the red tab is turned in. This is held in place by the 2x AA batte-
ries. Only when the batteries are installed will the unit be able to be placed on the ceiling plate. When one of the detectors enters the smoke or smo-
ke, the alarm will go off and it will be forwarded to other detectors that will also go off. If the smoke or walm disappears, the alarm will automatically
stop. To link with other SA-41 smoke detectors, the smoke detectors must first be logged on to each other. During registration, a code is wirelessly
agreed between all smoke detectors. As soon as a smoke detector goes off, it will send this code and other smoke detectors in the neighbourhood
will also go off. Please note that only the smoke detectors within a 20 meter radius of the smoke detecting smoke detector will sound.
Connecting:
Connect the smoke detectors to each other before installing the smoke detectors on the ceiling.
1) Take one of the smoke detectors.
2) Press and hold the button for 12 seconds until the light stops flashing and stays on. Now release immediately. (Repeat this step if the lamp starts
flashing quickly). The light will now remain on for 30 seconds.
3) During this time, briefly press the button on another SA-41 smoke detector, and release it immediately when the lamp lights up. If registration is
successful, the lights on both detectors will flash briefly.
4) Repeat step 3 for other smoke detectors you want to pair. You have another 30 seconds to do this.
5) Briefly press the button of the first alarm to stop the register procedure.
The maximum distance between each unit is 20 meters. Alarms that are outside this distance from a logged in Smoke Alarm will not alarm if it detects
a fire.
If you want to link an additional SA-41 later, you will need to repeat the entire registration process for all smoke detectors.
Time-out function:
This function will disable the alarm for approximately 10 minutes. This function can be activated by pressing the button once. The indicator light will
light up ± every 8 seconds to indicate that the sound has been temporarily muted. After 10 minutes, the alarm will be reactivated.
Test: The alarm is very loud (>85dB). We recommend using hearing protection when testing the smoke detectors. By pressing the test button on the
SA-41 the alarm can be tested.
1) Test a single alarm: Press the test button for at least 2 seconds. Operation is correct for 2 or 3 signal tones. Then the alarm is still working correctly.
2) Test all alarms: If you keep the test button pressed for a longer time (30 sec.), the connected smoke detectors within range will give an alarm to
indicate that the connection is OK. It may take up to 60 seconds for the other detectors to receive the signal. The button must also be held down for
this time.
If the connection does not work after 90 seconds of pressing and holding the test button, make sure that there are other devices nearby that work with
a radio connection and may cause interference.
If a single detector’s test does not work, check the battery. If it does not work with a new battery, replace the appropriate Smoke Alarm.
The test function does not work if the time-out function is enabled. Check the detectors every week. In alarm status, the smoke detectors generate at
least 85dB(A) of sound pressure. Do not test the smoke detectors with candles, open flames, cigarettes, or the like.
ATTENTION:
If there are questions about the cause of an ALARM, assume that the alarm is caused by a re and immediately evacuate the home.
Keep smoke detectors out of the reach of children.
During construction and renovation work, protect the smoke detectors from dust. Without protection, the smoke detectors lose their functionality.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Alecto SA-41 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Alecto SA-41 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.
The manual is 0,86 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
