794854

Alecto GA-10 Manual

9
Zoom out
Zoom in
Previous page
1/10
Next page
USE, TESTING AND MAINTENANCE:
USE:
The gas detector is operational if the 9 volt battery is placed and the GA-10 is connected by adapter. You can only place
the detector on the ceiling plate if the 9 volt battery is installed. If the detector is operational the red LED will blink. After
calibration it will turn green.
Once gas is detected, the alarm will go off. A loud beep will sound and the red LED will blink continuously. Once the
gas dissipates, the alarm will stop automatically.
Testing:
By pressing the test key on the GA-10, the alarm can be tested to ensure it is still operational. Hold the key for at least 2
seconds. Operation is correct if the red LED blinks and a tone is audible. Preferably check the detector weekly. During
alarm state, the GA-10 will generate a tone of at least 85dB(A) sound pressure.
Hush function:
With this function, the alarm will be deactivated for 5 minutes. This function can be activated by pressing the button
once, shortly. The red LED will blink to indicate the alarm is silenced. After 5 minutes, the blinking will stop and the
alarm will be reactivated
ATTENTION:
• If there is any doubt over the cause of an alarm, then assume the alarm is caused by a gas leak and evacuate the
premises as soon as possible.
• Keep the gas detector away from small children.
• During renovations, protect the gas detector against dust. It will lose it’s functionality if covered by dust.
Maintenance:
The GA-10 can be cleaned with a vacuum cleaner.
ENVIRONMENT:
Do not throw away used batteries, but recycle them using your local chemical depot. Product may not be thrown out as
normal waste, but must be recycled as electrical waste.
SPECIFICATIONS:
Usage temperature .........................................................................5°C tot 50°C
Power ...............................................................................................12VDC, 200mA 9V DC backup
Alarm point ......................................................................................< 15% LEL
Sound level during alarm ................................................................85dB at 1 meter
PROBLEM SOLUTION
No sound during the test procedure
Note: Hold the test button several
seconds during a test.
1. Remove the detector from the ceiling plate and check if the battery
and adapter is properly connected.
2. Clean the gas detector.
The gas detector beeps every minute Replace the 9V battery and check the adapter.
The gas alarm regularly gives a false
alarm during cooking or during use of
the shower.
1. Clean the gas detector.
2. Move the gas detector to another location.
Green LED blinks every 30 sec. Device not connected on main power, but works on battery.
Red LED blinks The device is still warming up or hush mode is active.
… 9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto GA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto GA-10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info