368259
28
Zoom out
Zoom in
Previous page
1/28
Next page
USERS MANUAL
DBX-88eco
2
LCD Language:
Depending on the purchased version, the LCD language might not be
English on start-up. Please see chapter 4.3 on page 8 how to change the
language of your DBX-88 eco.
1 ECO MODE
This Alecto DBX-88 ECO babyphone is equipped with an unique ECO
mode. Already in normal operation mode, the baby-unit stops transmis-
sion when the baby is not crying. In Full Eco mode it even suppresses
the controlling signals between the baby-unit and the parent unit, so no
transmitting at all.
Next to the Full eco mode, you can set the output power. In case you are
at home with your baby not far away, you can set the babyphone in half
range mode, with low transmitting power and reduced power consump-
tion. In case the baby is not close to you, you may switch to full range.
Attention: once the baby produces noise, the baby-unit is activated and
contacts the parent unit. This causes a small delay which means that
short sounds from the baby may not be heard by you. In case you really
want to hear all sounds from the baby room, you must set the sensitivity
to maximum (see chapter 4.6); with this setting the baby-unit is constantly
active.
3
2 OVERVIEW
2.1 OVERVIEW PARENT UNIT:
1. sound indication LED’s
2. volume up; up button when
programming
3. volume down; down button when
programming
4. button MENU/OK
5. link-check ( ), see below
6. loudspeaker
7. charge contacts
8. battery compartment
9. microphone
10. start/stop lullaby
11. display (see paragraph 2.3)
12. poweron/o
13. talk back
Link check :
asheswhenthereisnolinkbetweenbabyunitandparentunitor
parent unit is out of range with the baby unit.
on steadily when linked to the baby unit
in the full eco mode this lamp only lights when the parent unit actual
receives noise from the baby unit; in idle state this lamp is OFF
during FULL ECO mode
1
5
4
3
2
10
12
11
8
7
13
6
9
See also
chapter 4.15
in case this
lamp lights in
the orange
color
4
2.2 OVERVIEW BABY UNIT:
1. battery indication: see below
2. display (see paragraph 2.3)
3. built-in nightlight (not visible
when switched-off
4. power on/off
5. microphone
6. DC input for power adapter
7. start-stop lullaby
8. battery compartment (backside)
9. selection lullaby
10. loudspeaker
11. volume up/down
12. temperature sensor (back-
side)
13. page (to page the parent
unit)
14. nightlighton/o
battery indication :
lights when batteries are installed and the power adapter is connec-
ted to indicate that batteries are being charged (does NOT goes off
when batteries are fully charged)
6
5
3
2
1
11
10
1314
4
9
7 8
12
5
2.3 OVERVIEW DISPLAY:
on when night light is enabled
off when night light is disabled
on when lullaby is playing
on when the speaker volume is turned
off; off when the speaker volume is
turned on
on when sound alert is enabled
flashes when sound alert is triggered
indication temperature reading in Celsius or in
Fahrenheit
on when temperature alert is enabled, flashes when
temperature alert is triggered
on when the alarm time/count down timer is set, flashes
when the alarm time/count down timer is arrived
on when the FULL ECO MODUS is enabled
battery indication:
full battery level
2/3 battery level
1/3 battery level
battery empty
parent unit: this indication animates in cycle while charging. baby-unit: this indication does not light
when the power adapter is connected
displaying of the
several functions
and warnings
during use
displaying of the
several settings
during program-
ming
display parent unit
display baby-unit
6
3 INSTALLATION
3.1 PARENT UNIT:
The parent unit is powered by 2 supplied rechargeable batteries. These
batteries are charged through the included power adapter.
ATTENTION:
NEVER install normal batteries in the baby unit. Normal batteries
cannot be charged. Risc of explosion if battery is replaced by an
incorrect type.
1. Remove the belt clip with the help of a small screw-
driver
2. Remove the battery compartment cover.
3. Insert 2 x AAA rechargeable batteries, observing their
polarities, into the battery compartment on the parent
Unit. Only use the supplied batteries with the following
specifications:
voltage / capacity: 1.2V / 750mAh or more
material / size: NiMH, AAA, HR03
4. Replace the battery door on the Parent unit
5. Connect the output plug of the mains adapter to the DC socket on
the side of the baby unit and the mains adapter to the wall mains
supply.
As soon as the battery icon stops animating, the batteries are fully
charged (*). The LED on the charger pod remains on until you lift the
parents unit from the charger pod.
*: for the first time, it is recommended to continue charging for at least 24 hours, even when the
battery icon indicates that the batteries are full.
3.2 BABY-UNIT:
The baby-unit is powered by the supplied power adapter.
Only connect the provided power adapter with the following specificati-
ons: Input: 100-240VAC 150mA; Output: 9VDC 500mA
For portable use you can install 4 pcs RECHARGEABLE batteries.
7
ATTENTION:
NEVER install normal batteries in the baby unit. Normal batteries
cannot be charged. Risc of explosion if battery is replaced by an
incorrect type.
1. Remove the battery compartment cover.
2. Insert 4 x AA rechargeable batteries, observing their
polarities, into the battery compartment on the parent Unit. Only use
the supplied batteries with the following specifications:
voltage / capacity: 1.2V / 1300mAh or more
material / size: NiMH, AA, HR6, penlite
3. Reattach the battery compartment cover.
4. Connect the output plug of the mains adapter to the DC
socket on the side of the baby unit and the mains adap-
ter to the wall mains supply.
5. The battery indication comes on and charging begins (this LED
remains lit, even when the batteries are fully charged)
Depending on the capacity of the batteries, It will take about 24 hours to
fully charge the batteries.
The power adapter for the baby-unit is inclusive. Rechargeable batteries
for the baby-unit are exclusive.
3.3 RECOMMENDATIONS:
Never place the baby unit inside your baby’s cot, bed or playpen.
MAKE SURE THE BABY UNIT AND MAINS ADAPTOR CABLE ARE
ALWAYS OUT OF REACH OF THE BABY.
Avoid exposure of the units to moisture or liquid.
Clean the units with a damp cloth.
Do not expose the units to extreme heat or direct sunlight.
8
4 USING YOUR BABY MONITOR
Please read these instructions carefully, and be reminded that this baby
monitor is just intended as an aid. It is not a substitute for responsible,
correct parental supervision.
4.1 POWER ON/OFF:
provided the parent unit is off, press and hold
<POWER> for about 2 seconds to switch-ON
the unit
provided the parent unit is on, press and hold
<POWER> for about 2 seconds to switch-OFF
the unit
4.2 LINK CHECK:
As soon as the parent unit is turned on, it starts looking for the baby unit.
1. The link-led blinks and the text [SEARCHING] comes on the
display
2. As soon as the parent unit finds the baby unit, the link-LED lights
steadily
3. In case the parent unit cannot find the baby unit within a period of 30
seconds (because it is not yet switched on, the batteries of the baby-
unit are empty
or the distance is too large), the text [ NOT LINKED]
comes on the display and attention tones sound every 10 seconds.
See also paragraph 4.15.
4.3 LANGUAGE:
Itisrecommendedtorstsetthelanguagesothatalltextcomesonthe
LCD in your favorite language. By default the Dutch language is program-
med.
You only have to set the language onto the parent unit, the baby unit will
be synchronized automatically.
press the MENU button 2x
2 sec.
2 sec.
Menu
2x
9
ndtherequiredlanguage
press the MENUbuttontoconrmandtostore
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
4.4 MONITORING:
As soon as the baby unit detects a sound, it will send it to the parent unit.
receiving volume:
press the - button to decrease the volume or
the + button to increase the volume (5 levels +
volume-OFF)
the icon lights when the volume is set to off
(no sound)
You will hear an extra beep when the lowest or
the highest level is reached and when you press
the - or + button.
.
Optical indication:
the sound is also displayed visually by LED’s;
monitoring can therefore be carried out even
when the volume has been reduced or switched
oaltogether
4.5 TALK BACK:
press and hold TALK on the Parent unit to speak
to the baby
control the volume on the Baby unit:
press the - button to decrease the volume or the
+ button to increase the volume
- +
Menu
- +
Talk
- +
10
control the volume on the Parent unit:
press the MENU button
ndtheoption[BABYVOLUME]
press the MENU button
Set the required volume (attention: the actual
volume does not change yet)
press the MENUbuttontoconrmandtostore
the setting (only now the new volume setting will
be eective)
brieypressthePOWERbuttontoendthepro-
gramming mode
4.6 SENSITIVITY: (VOX)
You can adjust the sensitivity on the Parent Unit to monitor the sound
from Baby Unit:
press the MENU button
ndtheoption[SENSITIVITY]
press the MENU button
select the required level
There are ve levels of sensitivity which are
indicated by lighted blocks:
level 1 represents lowest sensitivity, level 4 re-
presents a high sensitivity, level 5 represents the
highest sensitivity (the microphone is activated all
the time)
(from factory the highest level is preset)
You will hear an extra beep when the lowest or the
highest level is reached and when you press the - or
+ button.
Menu
- +
Menu
- +
Menu
Menu
- +
Menu
- +
11
press the MENUbuttontoconrmandtostore
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
4.7 SOUND ALERT:
With the volume set to off, the babyphone can still warn you with beep-
tones that the baby is crying loud.
enable/disable sound alert:
press the MENU button
nd the option [ SOUND ALERT ]
press the menu button 2x:
ifthealertiscurrentlyo,itwillnowbesettoon;
ifthealertiscurrentlyon,itwillnowbesettoo
brieypressthePOWERbuttontoendthepro-
gramming mode
sound alert indication:
the icon is on when sound alert is enabled
and it flashes when the sound alert is triggered
4.8 LULLABIES:
5 Different lullabies are programmed into this babyphone
start/stop:
press button (baby-unit) or button
(parents unit) to start or to stop the playing of the
lullabies
(you can also press button on the baby unit to
start playing the lullabies)
Menu
- +
Menu
2x
Menu
12
lullaby indication:
the icon
is on when the baby unit is playing
lullabies
select lullabies from the Parent unit:
press the MENU button
ndtheoption[LULLABY]
press the MENU button
look for the desired lullaby
( [ PLAY ALL ] = play all songs)
press the MENUbuttontoconrmandtostore
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
select lullabies from the Baby unit:
press button to select another lullaby
( [ PLAY ALL ] = play all songs)
control the volume on the Baby unit:
Press the - button to decrease the volume or the
+ button to increase the volume
control the volume on the Parent unit:
press the MENU button
ndtheoption[BABYVOLUME]
press the MENU button
Menu
- +
Menu
- +
Menu
Menu
- +
Menu
- +
13
set the required volume (attention: the actual
volume does not change yet)
press the MENUbuttontoconrmandtostore
the setting (only now the new volume setting will
be eective)
brieypressthePOWERbuttontoendthepro-
gramming mode
Play time:
the maximum play time for one or for all lullabies
is 15 minutes
4.9 NIGHTLIGHT:
You can control the nightlight directly on the baby unit or remotely by the
parent unit.
control the nightlight on the Baby unit:
press the buttontoswitch-on/othenightlight
control the nightlight on the Parent unit:
press the MENU button
ndtheoption[NIGHTLIGHT]
press the menu button 2x:
ifthenightlightiscurrentlyo,itwillnowbesetto
on; if the nightlight is currently on, it will now be
settoo
brieypressthePOWERbuttontoendthepro-
gramming mode
night light indication:
the icon is on when the night light is switched
on
- +
Menu
15min.
Menu
- +
Menu
2x
14
4.10 ROOM TEMPERATURE AND ALERT:
In idle state the display of both the Baby unit and the Parent unit indicates
the temperature of the Baby room in degrees Celsius (°C) or in degrees
Fahrenheit (°F). With this option you can set the format, the limits and
enable or disable the Temperature alert.
press the MENU button
ndtheoption[TEMPERATURE]
press the MENU button
use the buttons -/+ to select between:
to alter between Celsius and Fahrenheit
to set the minimum temperature
(in between 10°C (50°F) and 20°C(69°F))
to set the maximum temperature
(in between 21°C (70°F) and 39°C(99°F))
to enable or disable the temperature alert
press the MENU button
use the buttons -/+ to change the settings
press the MENUbuttontoconrmandtostore
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
Menu
- +
Menu
- +
[ FORMAT ]
[ MIMIMUM ]
[ MAXIMUM ]
[ ALERT ON/OFF ]
Menu
- +
Menu
15
temperature alert indication:
the icon is on when the temperature alert is
enabled
working temperature alert:
If the temperature goes beyond the minimum or
maximum level, “COLD” or “HOT” indication dis-
plays and the current temperature flashes in the
displays of both Units.
If the Temperature alert is set to On, an alert will be sound at the Parent
Unit.
4.11 ALARM:
Alarm feature is useful for you to remind yourself for some special arran-
gements, like feeding time, etc.
press the MENU button
ndtheoption[ALARM]
press the MENU button
use the buttons -/+ to select between: [ OFF? ]
and [ SET TIMER ]
press the MENU button to disable the alarm
(to disable, now press MENU)
press the MENU button to set the alarm feature
1. pres the MENU button and use -/+ to set the
hours
2. pres the MENU button and use -/+ to set the
minutes
Menu
- +
Menu
- +
[ OFF? ]
[ SET TIMER ]
16
3. pres the MENU button and use -/+ to toggle
between [ ONCE ] and [ REPEATED ]
4. press the MENU button to conrm and to store
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
alarm indication:
the icon is on when the timer is activated;
in the lower part of the display you can see the
timer time
working alarm:
in the lower part of the display you can see the alarm time; when it
reaches 00:00 it will beep for up to 30 seconds; press any button to stop
the alarm; in case you selected [ REPEATED ] now the alarm starts again
with the count down
a repeated alarm can be disabled by selecting OFF in the menu or by
switching off of the parent unit
4.12 PAGING THE PARENT UNIT:
Use this feature to call the parent unit in case you need help in the baby
room or to find the parent unit. The parent unit must be switched-on to use
this feature.
press the Page button to generate tones at the
parent unit for 120 seconds; the text [ Paging ]
comes on the display
You may end this signaling by again pressing button Page or by
pressing any key on the parent unit.
The volume of these tones is fixed.
In case the volume of the parent unit was set to off, when paging the
volume will be set to on and remain on.
Page
Menu
- +
17
4.13 RANGE:
In case you are close to you baby, you might decide to reduce the trans-
mitting power
press the MENU button
ndtheoption[ECORANGE]
press the MENU button
depending on the present setting, when pressing
the button MENU you now set the babyphone
into [ HALF RANGE? ] or [ FULL RANGE? ] (*)
press the MENUbuttontoconrmandtostore
the setting
brieypressthePOWERbuttontoendthepro-
gramming mode
* The power setting only takes eect 30 seconds after the baby unit is
idle (no transmitting). The eective ranges depend on your local circum-
stances and should be found out empirically.
4.14 FULL ECO:
When FULL ECO is activated, there is no transmitting at all when the
baby is not crying.
press the MENU button
ndtheoption[FULLECO]
press the menu button 2x: if the Full Eco Mode is
currentlyo,it
will now be set to on; if the Full Eco
Mode
iscurrentlyon,itwillnowbesettoo
Menu
- +
Menu
Menu
[ HALF RANGE ? ]
[ FULL RANGE? ]
Menu
- +
Menu
18
FULL ECO indication:
turns on when the FULL ECO mode is
enabled
Remarks regarding FULL ECO
Lullaby playback and a maximum sensitivity (level 5, see chapter 4.6) will
temporarily disable the Full ECO feature if Full ECO setting is set to ON.
The icon
however will still be on
.
Attention: The link check is not active in Full Eco mode; see the next
chapter.
4.15 LINK CHECK:
Automatic:
When the FULL ECO is disabled, the babyphone constantly checks the
link between the baby-unit and the parents-unit:
As soon and as long the parent unit is in contact with the baby unit,
the link-LED on the parent unit lights steadily.
When the baby unit gets out of range (or is powered off), the link-LED
on the parent unit starts blinking and the text [ SEARCHING ]
comes on the display.
In case the link is not restored within 30 seconds, a beeptoon sounds
every 10 seconds and the text [ NOT LINKED ] comes on the display.
Once the link between the parent unit and the baby unit is restored,
the link-LED will light steadily and the text [ NOT LINKED ] will disap-
pear from the display.
19
Manual:
The link check does not function when the FULL ECO MODE is set. The
-LEDisoandyouwillnotbewarnedwhenyouareoutofrangeof
thebaby-unitorwhenthebabyunitisswitched-o.
As follow you can however check the link manually
1. Press button TALK for about 0.5 seconds (*):
2. Link OK:
turns on and for a
couple of seconds you will
hear all sounds from the
baby-room
3. After some seconds the
FULL ECO MODE is
activated again and
turnso
*: if you press button TALK for a longer period, the feature TALK BACK
is activated and you might wake up the baby.
4.16 BATTERY INDICATION:
Both the parent unit and the baby unit are equipped with a battery level
indicator in the display:
: full battery level
: 2/3 battery level
: 1/3 battery level
: battery empty
Baby-unit:
the battery indicator is off when the baby unit is powered by the
power adapter
the battery indicator is on and indicates the capacity when the baby
unit is powered by batteries
2. No link:
turnsonbutstartsashing;you
will not hear any sound from the
baby-room and after 30 seconds you
will hear beeps as an indication that
there is no link
3. As soon as you have found the
cause of the no-link warning and
solved it, the FULL ECO MODE will
be activated again and will turn
o
20
when the battery indicator on the baby unit indicates flat batteries
( ), the text [ BU LOW BATT! ] comes on the display of the
parent unit; it is advised to now directly replace the batteries in the
baby unit or to connect the power adapter; (attention: when the
parent unit is in the alarm mode, this warning text will not come on
the display)
in case you do not change the batteries or do not connect the power
adapter, the baby unit will switch off after a while; the link-LED on the
parent unit will start blinking and the text [ NOT LINKED ] will come
on the display of the parent unit; after you replace the batteries or
connect the power adapter, the set functions as normal again
Parent unit:
the charging of the batteries is indicated with an animated battery
icon; as soon as the batteries are charged, this icon shows ‘battery
full’ ( )
in idle state this icon shows the actual capacity of the batteries
soon after the battery icon shows ‘empty batteries’ ( ), the parent
unit will switch-off; reconnect the power adapter to get the parent unit
function again
4.17 BELT CLIP:
On the backside of the parents unit you will find the belt clip to carry the
unit around while keeping your hands free.
Use a small screwdriver to remove this clip if you want.
21
4.18 RESTORE TO DEFAULT:
As follow the settings of the babyphone can be restored to the default
values:
Parent unit:
press the MENU button
ndtheoption[RESET]
press the MENU button 2x
The parent unit switches off and on again and the settings are restored
to their default values:
Sensitivity: level 5 (maximum sensitivity, the microphone is
activated all the time)
Night light: on
Language: Dutch
Lullaby: lullaby 1
Sound alert: off
Volume baby-unit: level 3
Alarm: off
Temperature format: Celsius
Temperature alert: off
Lower limit: 14
Upper limit: 39°C
Volume parents-unit: level 1
Full Eco Mode: off
Range:
maximum
Menu
- +
Menu
2x
22
5
(SAFETY) INSTRUCTIONS
AND TIPS
5.1 GENERAL:
The Babyphone is for the detection of sound by which the guarding
of babies, little children and the helpless is a common used feature.
Be advised that this babyphone is never capable to meet with the
presence of an adult or a parent.
Each time before use, check the functionality of the set. Be advised
to regularly check the link during use.
The use of the babyphone is restricted to detection of sounds within
own premises. Any other person who is present or might be present
within the room that is monitored should be notified of the presence
of the installed babyphone.
The usage of the wireless room monitor is free of license. It cannot
be guaranteed that the transmission is without interference caused
by other wireless systems or atmospheric disturbance.
In case the babyphone is not in use, please switch-off using the
power button. If not in use for a longer period, disconnect the power
adapter and remove the batteries.
5.2 MULTIPLE UNITS:
It is not possible to extend this babyphone with multiple parent units
or multiple baby units. In case more baby’s are to be watched, some
more complete units should be purchased. These can be used next
to each and will not disturb each other.
5.3 TEMPERATURE INDICATION:
The temperature sensor is located on the backside of the baby unit.
To ensure a correct reading you may not cover this sensor or place
the unit in direct sunlight. Avoid placing next to a heating device. The
range is 10°C to 39°C. Attention: the temperature indication is indica-
tive only. Please count with a possible deviation of about 5% to10%.
23
5.4 REACH:
The reach of the babyphone is approximately 50 meters indoor and
300 meter outdoor. Please be informed that large buildings, metal
constructions, atmospheric disturbances and other wireless devices
can influence this reach.
5.5 BATTERY LIFE TIME:
Parent unit:
With fully charged rechargeable batteries with a capacity of 750mAh
you can use the parent unit for up to 24 hours without the power
adapter.
Baby unit:
When alkaline batteries are installed, the baby unit will function for
about 48 hours without the power adapter.
5.6 POWER SUPPLY:
Power adapters:
Use only the mains adapters supplied with this baby monitor.
Incorrect adapter type(s) can cause damage to the unit(s).
Adapter baby-unit:
Model: S004LV0900050
Input: 100-240VAC 150mA; Output: 9VDC 500mA
Adapter charger pod:
Model: S004LV0600045
Input: 100-240VAC 150mA; Output: 6VDC 450mA
Batteries:
Only install RECHARGEABLE batteries in both the parent unit and
the baby-unit:
Baby-unit: 4 x 1,2V NiMH AA
Ouder-unit: 2 x 1,2V NiMH AAA
5.7 MAINTENANCE:
Never use chemical cleansers to clean the cabinet, the cabinet may
only be cleaned with a moist cloth.
Always disconnect the babyphone from the mains (remove the
power adapters) before cleaning.
24
5.8 DISPOSAL OF THE DEVICE (ENVIRONMENT):
At the end of the product lifecycle, you should not throw this
product into the normal household garbage but bring the
product to a collection point for the recycling of electrical
and electronic equipments. Exhausted batteries may never
be disposed of in household waste but must be handed in at your
local depot for chemical waste.
6
DECLARATION OF CONFORMITY
Hereby, Hesdo declares that the radio equipment type Alecto
DBX-88 is in compliance with directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the fol-
lowing internet address: http://DOC.hesdo.com/DBX-88-DOC.pdf
7 TECHNICAL SPECIFICATIONS
No. of channels: 120
Frequency: 1880-1900 Mhz
RF power: <24 dBm
Power supply of Baby Unit: Switching mode power supply
9V/500mA/ (incl.)
4x 1.2V AA NiMH rechargeable
batteries (excl.)
Power supply of Parent Unit: Switching mode power supply,
6V/450mA/ (incl.)
2x 750mAH NiMH rechargeable
batteries (incl.)
Operating temperature: 10°C to 40°C
Storage temperature: 0°C to 60°C
Temperature accuracy: ±1°C (at 25°C)
25
8 TROUBLESHOOTING
In case the babyphone still does not operate correctly, please disconnect
the power adapters and remove the batteries. Wait for some minutes
and install batteries and connect the power adapters again. In case the
malfunction still persists, please contact your dealer.
PROBLEM:
LED
ashes
LED
ashes+
attention tones
from parent unit
Cannot hear
sound or baby
cry from the
parent unit
The sound on
the parent unit is
interrupted
High-pitched
tone
POSSIBLE SOLUTION:
The parent unit and the baby unit may be out of
range with each other. Reduce the distance between
the units.
Thebabyunitmaybeswitchedo.PressPOWER-
key to switch on the baby unit.
Lost connection with the baby unit. Reduce the dis-
tance between the parent unit and the baby unit.
Thebabyunitmaybeswitchedo.PressPOWER-
key to switch on the baby unit.
Rechargeable batteries in baby-unit are empty.
Connect the baby unit to the mains power with the
supplied power adaptor for recharging.
The volume level in the parent unit may be set too
low, increase the volume level of the parent unit.
The microphone sensitivity level of the baby unit may
be set too low. Increase the sensitivity level of the
baby unit.
The parent unit and the baby unit are too close to
each other. Make sure the parent unit and baby unit
are at least 1.5 metre away from each other.
The speaker volume of the parent unit maybe set too
high. Decrease the volume of the parent unit.
26
9 CONTENTS
1 ECO MODE ......................................................................2
3
2 OVERVIEW
2.1 OVERVIEW PARENT UNIT .............................................3
2.2 OVERVIEW BABY UNIT .................................................. 4
2.3 OVERVIEW DISPLAY ......................................................5
3 INSTALLATION
3.1 PARENT UNIT ..................................................................6
3.2 BABY-UNIT ......................................................................6
3.3 RECOMMENDATIONS ....................................................7
4 USING YOUR BABY MONITOR
4.1 POWER ON/OFF .............................................................8
4.2 LINK CHECK ....................................................................8
4.3 LANGUAGE .....................................................................8
4.4 MONITORING ..................................................................9
4.5 TALK BACK ......................................................................9
4.6 SENSITIVITY ...................................................................10
4.7 SOUND ALERT ................................................................ 11
4.8 LULLABIES ......................................................................11
4.9 NIGHTLIGHT....................................................................13
4.10 ROOM TEMPERATURE AND ALERT .............................14
4.11 ALARM ............................................................................. 15
4.12 PAGING THE PARENT UNIT ..........................................16
4.13 RANGE ............................................................................17
4.14 FULL ECO ........................................................................ 17
4.15 LINK CHECK ....................................................................18
4.16 BATTERY INDICATION ...................................................19
4.17 BELT CLIP........................................................................20
4.18 RESTORE TO DEFAULT .................................................21
5 (SAFETY) INSTRUCTIONS AND TIPS
5.1 GENERAL ........................................................................22
27
5.2 MULTIPLE UNITS ............................................................22
5.3 TEMPERATURE INDICATION ......................................... 22
5.4 REACH .............................................................................23
5.5 BATTERY LIFE TIME ....................................................... 23
5.6 POWER SUPPLY ............................................................. 23
5.7 MAINTENANCE ...............................................................23
5.8 DISPOSAL OF THE DEVICE (ENVIRONMENT) ............24
6 DECLARATION OF CONFORMITY ................................24
7 TECHNICAL SPECIFICATIONS .....................................24
8 TROUBLESHOOTING .....................................................25
9 CONTENTS .....................................................................26
10 GUARANTEE ..................................................................28
28
10 GUARANTEE
You have a guarantee of 24 MONTHS after the date of purchase of this
babyphone. We guarantee during this period the free repair of defects
caused by material- and construction faults. This at the importers discre-
tion. It is only possible to claim to the guarantee when you enclose your
purchase ticket with the babyphone.
HOW TO ACT:
If you notice a defect, consult the manual first. If this manual gives you
no definite answer, consult your dealer with a clear description of your
complaint. He will collect the device together with this guarantee card
and the dated purchase ticket and he will take care of a prompt repair,
respectively free sending to the importer.
THE GUARANTEE EXPIRES:
When used inexpert, faulty connections, leaking and faulty placed bat-
teries, use of unoriginal parts or accessories, negligence and defects
caused by fire, flood, stroke of lightning and natural disasters. With un-
qualified modifications or repairs by third persons. With incorrect transport
without a suitable packing. If the device is not handed in with the correct
filled in guarantee card and the purchase ticket.
NOT UNDER THIS GUARANTEE: cords, plugs and batteries.
All further responsibilities, in particular subsequent damages, are exclu-
ded.
ver GB5.3
Service
Help
Service Help
WWW.ALECTO.NL
SERVICE@ALECTO.NL
Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW.ALECTO.NL
SERVICE@ALECTO.NL
Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch,
The Netherlands
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto dbx-88 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto dbx-88 in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alecto dbx-88

Alecto dbx-88 User Manual - German - 28 pages

Alecto dbx-88 User Manual - Dutch - 22 pages

Alecto dbx-88 User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info