708462

Alecto ADB-11 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Change melody:
melody-1
~
melody-36
1x
v1.0
Service
Help
Service Help
WWW.ALECTO.NL
SERVICE@ALECTO.NL
Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW.ALECTO.NL
SERVICE@ALECTO.NL
Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch,
The Netherlands
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
1x
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
Volume H
Volume M
Volume L
Frequency: 433MHz ASK
Transmission power: <10mW
Declaration of conformity:
http://DOC.hesdo.com/ADB-11-DOC.pdf
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto ADB-11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto ADB-11 in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info