Manual Alde Comfort 2928 (page 8 of 16) (English, German, Swedish)

626264

Zoom out

Zoom in

1/16

Chapter Page

Technical data 81.

Fitting the boiler 82.

Mounting a boiler in a cupboard 82:1

Fitting the ue terminal 92:2

LPG Installation 92:3

Fitting the room thermostat 92:4

Electrical installation 92:5

Fitting the heating system 103.

Connection to the heating system 103:1

Filling the heating system 103:2

Connection to hot water heater 114.

Installation inspection 115.

Read through these installation instructions carefully

before tting the boiler. The installation instructions

are approved in accordance with CE no. 048 AO-0007

for LPG boiler type 2928. In connection with follow-up

inspection of the boiler, national regulations must be

followed.

IMPORTANT WARNING!

No unit should be installed in any enclosed space

unless additional permanent ventilation of 100 cm

provided. No alteration or adjustment should be made

to any gas burner or gas supply by unauthorised or un-

skilled persons. In the event of a failure or breakdown,

turn off the gas supply at the cylinder and contact the

authorised dealer or supplier.

The installation must be carried out in accordance with

the relevant British Standard of Practice. (Particulary

BS5482 Parts 1, 2 and 3).

The Gas Safety Regulations issued by the Dept. of

the Environment, the Building Standards (Scotland)

(Consolidaton) Regulations issued by the Scottich

Develop ment Department.

In any communication it is essential to quote the model

and serial number shown on the data badge.

TECHNICAL DATA1.

Dimensions: Height Width Depth

Boiler dimensions: 1710 mm 132 mm 220 mm

Min. space required: 1850 mm 132 mm 400 mm

With immersion heater: 1850 mm 132 mm 450 mm

With immersion heater

and water heater: 1850 mm 132 mm 480 mm

Gas: Propane Butane

Power: 5,8 kW 6.7 kW

Gas consumption: Max 420 g/h Max 480 g/h

Gas pressure: I

28-30/37 mbar, I

3B/P

30 mbar.

Weight of LPG boiler: 19 kg

Weight of immersion heater: 2.5 kg

(plus 0.5 kg for motor)

Weight of water heater 2959: 4.5 kg

Liquid volume in boiler: 2.6 l

Liquid volume in immersion heater: 1.0 l

FITTING THE BOILER2.

Mark out where the boiler is to stand. If the boiler is

to be positioned against a wall or bulkhead made of a

inammable material, a 1 mm air gap must be allowed.

Make holes in the oor, one for the ventilation duct and

one for the drainage hose (see g 1). The ventilation

duct can be placed either on the right-hand side or the

left-hand side, depending on space available. Cover

the hole for the ventilation duct with ne mesh netting.

Fit the chimney according to chapter 2:2.

Put a strip of realant round where the boiler is to stand.

Position the boiler and screw it in place on the oor

and wall at A g 2.

Remove the square panel on the side boiler where the

ventilation duct is to be tted by pressing the panel out

from inside the boiler casing and cutting the insula-

tion around the aperture with a sharp knife. Uncoil the

overow hose and pass down through the duct and out

through the hole in the oor. Screw the duct to the oor

and the side of the boiler.

If the boiler is tted in a cupboard a partition should be

installed to prevent inammable materials from con-

tacting hot parts of the casing etc. When immersion

or water heaters are tted cut holes in the partition, as

g. 4 for access to the water heater air cock and the

overheat reset button for overheating protection on the

immersion heater.

Fig 1

Hole for ventilation ductA.

Drainage hoseB.

Fig 2

Hole for attaching boilerA.

Fresh airB.

Protection for the exhaust pipeC.

Upper front plateD.

Lower front plateE.

Preheated fresh airF.

Carrying handleG.

Intake hoseH.

Hose clipI.

Drainage hoseJ.

Fig 3

Hole for air screw on water heater type 2959.A.

Hole for drain cock on water heater type 2959.B.

Hole for reset button for overheating protection on C.

immersion heater.

Mounting a boiler in a cupboard2:1

Mark out where the boiler is to stand. An air-space of

1 mm must be left if the boiler is to be placed next to a

wall or anything else that consists of ammable mate-

rial. A door or service hatch should be placed in front of

the boiler so that the control panel and the expansion

tank are easily accessible. The minimum distance in

front of the boiler to any ammable material should be

5 mm. Ventilation areas for the space which the boiler

is to occupy should be at least 10 cm2 at the oor

and the roof. Make holes in the oor, one for the input

Where can I get an Alde control house and lid in EUROPE for a 2923/2928? Submitted on 29-8-2021 at 17:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alde Comfort 2928 in the language / languages: English, German, Swedish as an attachment in your email.

The manual is 1,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alde Comfort 2928

Alde Comfort 2928 User Manual - English, German, Dutch, French, Swedish, Finnish - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alde Comfort 2928 Manual

Product: