601609
17
Zoom out
Zoom in
Previous page
1/140
Next page
Assembly
462706_i 17
5 Put the log splitter in vertical position (piston
rod upright) and screw the support foot (4) on
the rear feet.
6 Erect the log splitter and mount the cross
members in front (6a) with the help of the
threaded rod (6b).
Mains connection
1 Connect the cable to the mains supply.
STARTUP
CAUTION!
The log splitter should not be operated if
components (e.g. the protective hoops)
are missing or defective or the connec-
tion cable is damaged.
Prior to every use
CAUTION!
Before operating the log splitter on the
ground needs to be fixed, and thus be
secured against falling over!
1 Conduct a visual inspection of the log splitter.
2 The log splitter should not be operated if com-
ponents are missing, defective or loose.
3 Visually inspect the connection cable. A de-
fective connection cable (e.g. with cracks,
cuts, crushing damage or bends in the insu-
lation) should not be used.
4 Visually inspect the hydraulic components for
leaks.
5 Fix log splitter with appropriate means on the
ground
Log splitter start-up
CAUTION!
The transportation wheels are only used
to transport the log splitter.
During splitting operation, the wheels
must be removed from the feet and
mounted in the park position (12).
CAUTION!
Never lay the log on the splitter in trans-
verse direction, see Illus. 10. Never force
the splitting of a log by sustaining the hy-
draulic pressure over several seconds.
CAUTION!
The log splitter should only be used by
one person.
ADVICE
After splitting, tighten the venting screw
(7) again .
1 Position the log splitter horizontally on a level,
firm surface, better with a slight inclination
towards the operating lever (since the valves
are seated here). If inclined towards the split-
ting wedge it loses splitting force. Do not de-
posit the log splitter on the connection cable!
2 Lay the connection cable so that it cannot be
damaged by bending, crushing or otherwise.
3 Loosen the venting screw (7) by 3-4 turns.
4 Depending on the length, lay the log such that
the wooden log is held by the log guide tubes.
OPERATION
CAUTION!
Only the operator is allowed to remain
within the operating area during opera-
tion! (13)
1 With one hand, press the switch on button of
the electric motor (8a) and hold it pressed.
2 After the motor has attained its end speed,
press the operating lever with the other hand
(8b) fully downwards. The log pusher will
press the log against the splitting wedge. The
log will be split.
3 By releasing the switch-on button and the
operating lever, the log pusher moves back
into its end position.
Remove a jammed log (9)
CAUTION!
Never use a hammer to drive out the
piece of wood.
When the piece of wood springs out, it
might injure people and damage the ma-
chine.
1 Remove both your hands from the switch-on
button and operating lever
2 Letting log pusher grind to a halt
3 Push the wood wedge under the jammed
piece of wood (9)
4 Use the log pusher to push the wood wedge
all the way under the jammed piece of wood
5 Repeat with a larger wedge if necessary until
the piece of wood is released
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko KHS 3704 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko KHS 3704 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info