Manual Al-ko HW 604 INOX (page 11 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish)

601988

Zoom out

Zoom in

1/116

GB 3



When operating the system (

automatic

operation), take appropriate measures to

ensure that damage due to flooding can-

not occur if the system should

malfunction.

Attaching the suction hose

Choose a hose which is long enough so

that the device will not suck in air and run

dry. The hose should be at least 30cm

under the surface of the liquid to be

pumped while the pump is in operation.

Mount a non-return valve in the suction

hose to prevent the liquid from running

back out of the pump.

• Attach the suction hose. Make sure to

screw it in tightly, but take care not to

damage the threads.

If the liquid to be pumped is deeper than 4

m, you should use a suction hose which is

larger than 1“ in diametre for the best

performance. We recommend our AL-KO

suction set (14), which consists of a

suction hose, strainer and non-return

valve. The suction set is available at your

local retailer’s.

Before pumping sandy water, you must

insert a filter (13) between the suction

hose and the pump inlet or you will dam-

age your domestic water system. The

filter is available at your local retailer’s.

•

When laying the suction hose, make

sure that it is lower than the system.

If the suction hose is laid so that it is

higher than the device, bubbles will be-

come trapped in the line and the pump

will suck air.

Attaching the pressure hose

• Attach the pressure hose. Make sure to screw it

in tightly, but take care not to damage the

threads.

Filling the pump

Before putting your domestic water sys-

tem into operation, you must fill the pump

chamber with water until it overflows to

achieve full suction power. Do not operate

the pump while it is dry because this will

cause serious damage to the pump.

• Remove the filler screw (2).

• Pour water into the opening until the chamber

of the pump (12) is full.

• Replace the filler screw (2) and tighten it.

Switching on the system

• Open the pressure line (open valve, sprayer,

tap, etc.).

• Plug the electric cable into the socket. The

pump will automatically begin to run.

• As soon as the flow of water is cleared of air

bubbles trapped in the line, close the pressure

line. When the pressure has fallen and the

reservoir is full, the pump will automatically

switch off. Your domestic water system is now

ready for operation.

Switching off the system

• Switch the system off by unplugging the

electric cable from the socket.

Maintenance and Cleaning

Before beginning any maintenance or

cleaning work, make sure that the device

has been unplugged and take precautions

to ensure that it cannot be switched on

during work!

Cleaning the system

If you have used your domestic water system to

pump chlorine water (swimming pool water) or

liquids which leave a residue, flush your pump out

with clear water after use.

Clearing blockages

If your domestic water system should become

blocked so that it does not suction or pump out

liquid, remove the obstruction as follows:

• Remove the suction hose from the pump inlet

(1).

• Attach the pressure hose to the water tap and

spray water into the pump chamber until the

blockage is flushed out.

• Check to see that the obstruction has been

cleared entirely by switching on the pump for a

short time. Do not let the pump suck air.

• If the pump runs trouble-free, put it into opera

tion as described in the instructions.

Frost protection

Your domestic water system is susceptible to low

temperatures. Make sure to empty the device of

residual liquid (hoses, pump and reservoir) and

store it so that it is protected from frost.

• Empty the suction and pressure hoses.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko HW 604 INOX in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 4,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko HW 604 INOX Manual

Product: