594626

Al-ko COMBI CARE 38E COMFORT Manual

15
Zoom out
Zoom in
Previous page
1/152
Next page
15
474 397_b
GB
The correct working depth depends on:
the condition of the lawn
the wear on the blades
If the working depth is incorrect:
the scarifier will stop
the motor will stall
In this case, move the dial selector back to a shallower
working depth.
Always mow the lawn before scarifying.
Starting the motor
1. Push and hold the button of the safety pushbutton
switch.
2. Pull the operator presence control against the
handlebar. The motor starts.
The operator presence control does not lock in
place. It must be held in place all the time.
3. Release the button of the safety pushbutton
switch.
Switching off the motor
1. Release the operator presence control. It automati-
cally returns to its initial position. The motor is
switched off.
Danger of lacerations!
The blade shaft keeps turning under its own
momentum! After switching off, do not reach
under the machine straight away.
Hooking in/unhooking the grass catcher
1. Switch off the motor before hooking in/unhooking
the grass catcher.
2. Wait for the blade shaft to come to a stop
General notes on operation
The blade system must be able to turn entirely
freely in order for the machine to be started
Keep the power cable out of the working area
Do not place your hands and feet close to any
rotating parts
Only control the machine using the handlebar. This
ensures the necessary safety clearance.
Be particularly careful when turning the scarifier or
if you are pulling the machine behind you
Make sure you can stand securely on slopes
Always scarify across the slope
Never scarify on steep slopes
Always scarify at walking pace
Never tilt or transport the machine when the motor
is running
Have the machine checked by a specialist if the
following events occur:
After running into an obstacle
If the motor stops suddenly
If a blade is bent
If the blade shaft is bent
If the V-belt is defective
Maintenance and care
Danger!
Risk of injury on the blade shaft.
Wear protective gloves!
The user cannot open the motor enclosure for
maintenance, such maintenance must be done
by an authorised specialist workshop.
Disconnect the mains plug before any mainten-
ance and cleaning work! Wait for the shaft to
come to a stop.
Only use genuine spare parts.
Only renew worn or damaged implements and
pins as a set, in order to avoid imbalances.
Do not spray the machine with water!
Water ingress can cause irreparable damage to the
motor and the safety pushbutton switch.
Clean the machine after each use (scraper, cloth,
etc.).
Removing the blade shaft (Fig. H)
1. Unscrew and remove the screw (1) of the bearing.
2. Fold up the bearing half (2).
3. Lift the blade shaft out of the lower bearing half
and pull it out of the drive side (3).
Install in the reverse sequence.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko COMBI CARE 38E COMFORT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko COMBI CARE 38E COMFORT in the language / languages: All languages as an attachment in your email.

The manual is 6,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info