594627

Al-ko Combi Care 38 P Comfort inkl. Box Manual

13
Zoom out
Zoom in
Previous page
1/180
Next page
Startup
474398_b 13
In case the cutting height is not correct:
the scarifier stands still
the engine does not pull through
IIn this case, set the knob to a lower cutting height.
ADVICE
Before mowing the lawn scarifying fore-
ver.
Starting the engine
Starting with a cold engine, after longer periods of
storage and temperatures under 10°C:
1. Press pimer button “a” 6 times. (picture K).
2. Press pimer button “b” 10 times. (picture K).
3. Press control button and simultaneously pull
engine bar up to handle bar and hold it there
(picture L).
ADVICE
You must hold the engine control bar
tight during use.
4. Quickly pull out the starter cord and then allow
it to slowly roll up (picture M).
5. Let the engine run until it is warm.
ADVICE
Do not press primer buttons when en-
gine is warm.
Engine speed (rpm value) is fixed. En-
gine speed cannot be adjusted.
Turn the engine off
1. Release the control bar (picture L).
WARNING!
Risk of injuries due to turning spind-
les!
The cutter spindle does not stop turning
immediately. Do not touch the bottom of
the equipment shortly after switching off.
Installing and removing the grass catcher
1. Turn the engine off before installing/removing
the grass catcher.
2. Wait until the cutter spindle has come to a
complete stop!
General operation instructions
To start the equipment, the cutting unit must
be freely movable.
Keep hands and feet away from rotating
parts.
Control the equipment only through the
handle. Thus the safety distance is guaran-
teed.
Keep exhaust and engine clean.
Always ensure you have a good foothold on
slopes.
Move across slopes, never up or down.
Do not use on steep slopes.
Guide the machine at walking pace.
Never tilt or transport the device with the en-
gine running.
Have a professional check:
after bumping against an obstacle
if the engine stops suddenly
if the blade is bent
if the cutter spindle is bent
if the belt is damaged.
MAINTENANCE AND CARE
DANGER!
Risk of injury at the cutter spindle. Wear
protective gloves!
Remove the spark plug connector before any
maintenance or cleaning jobs!
Do not spray water on the equipment! Water
infiltration (ignition system, carburetor) can
cause faults.
Clean the equipment after each use (spatula,
cloth).
Removing the scarifier roller (picture N)
1. Remove the bearing screw (1).
2. Tilt the bearing halves (2) upwards.
3. Lift the scarifier roller from the lower bearing
half and extract it out from the drive side (3).
Assembly is carried out in reverse order.
Removing the aerating roller
Removal of the aerating roller and replacement of
steel spring hooks are similar to scarifier roller.
Removing the blades (picture O)
ADVICE
Before removing the blades observe the
mounting position!
1. Unscrew the hexagonal bolt (1).
2. Carefully remove the ball bearing (2) from the
spindle (8).
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko Combi Care 38 P Comfort inkl. Box at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko Combi Care 38 P Comfort inkl. Box in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info