594595
8
Zoom out
Zoom in
Previous page
1/248
Next page
D
Technische Daten
8 130 H
TECHNISCHE DATEN
130 H
Motortyp 4-Takt
Hubraum 35,8 cm³
Leistung 1,2 kW
Betriebsgewicht ohne
Benzin
7,3 kg
Treibstoffmenge 0,65 l
Zündung elektronisch
Zündkerze CM5H (NGK)
Antrieb Fliehkraftkupplung
Griff „Bike“-Griff
Schallleistungspegel 107 dB(A)
Schalldruckpegel 95 dB(A)
Vibration 4,3 m/s
2
K = 2,5 m/s
2
Schnittbreite Blatt 25 cm
Drehzahl Motor max. 7000 U/min
Drehzahl Motor Leer-
lauf
2780 U/min
MONTAGE
ACHTUNG!
Das Gerät darf erst nach vollständiger
Montage betrieben werden.
Bike Griff montieren
siehe Abb. 2
1 Sternschraube aus der Griffstütze heraus-
schrauben.
2 Beide Halbschalen von der Griffstütze ab-
nehmen.
3 "Bike"-Fahrradgriff in die Halbschalen einle-
gen.
4 "Bike"-Fahrradgriff und Halbschalen auf die
Griffstütze aufsetzen.
5 Mit Sternschraube festschrauben.
Schutzhaube montieren
siehe Abb. 3
1 Motorsense so legen, dass die Arbeitswelle
nach unten zeigt.
2 Das Schaftrohr anheben und den Schutz (1)
an der Unterseite des Schaftrohres entlang in
die richtige Position schieben (auf Anschlag
am Winkelgetriebe).
3 Das Schaftrohr mit dem Schutz ablegen.
4 Das Befestigungsteil (2) zuerst mit einer
Schraube 5 x 20 mm durch die Bohrung (a) a
am Schutz festschrauben.
5 Danach erst die zweite Schraube 5 x 20 mm
durch die Bohrung (b) nur leicht eindrehen.
HINWEIS
Das Befestigungsteil (2) hat innen bei
der Bohrung (a) ein Erhöhung. Da-
her kann die erste Schraube durch die
Bohrung (a) gleich auf Block festgezo-
gen werden ohne dass die Verbindung
Schräg sitzt
siehe Abb. 4 und 3
1 Die Motorsense dann so legen, dass die Ar-
beitswelle nach oben zeigt.
2 Mit den 2 Schrauben 5 x 35 mm durch die
Bohrungen am Halteblech des Winelgetrie-
bes den Schutz und das Befestigungsteil
festschrauben. Eventuell die Lage des Schut-
zes vorher korrigieren, die Bohrungen müs-
sen genau übereinander liegen.
3 Die Schraube in der Bohrung (b) endgültig
festziehen.
Schneidmesser montieren
siehe Abb. 5
1 Die Motorsense so legen, dass die Arbeits-
welle nach oben zeigt.
2 Das Schneidwerkzeug auf das Druckstück
(1) auflegen.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko AL-KO 130 H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko AL-KO 130 H in the language / languages: All languages as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info