Manual Al-ko 636 (page 33 of 622) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

601599

Zoom out

Zoom in

1/622

3. SAFETY REQUIREMENTS

469601_a 33

B) PREPARATION

1) Always wear adequate clothing which does

not hamper movements when using the ma-

chine.

– Always wear slim-fitting protective clothing,

fitted with shear-proof protection devices.

– Always wear a helmet, protective gloves,

eye-goggles, a half-mask respirator and

safety anti-shear boots with non-slip soles.

– Always wear ear and hearing protection de-

vices.

– Never wear scarves, shirts, necklaces, or

any hanging or flapping accessory that could

catch in the machine or in any objects or ma-

terials in the work area.

– Tie your hair back if it is long.

2) WARNING: DANGER! Fuel is highly flamma-

ble:

– keep the fuel in containers which have been

specifically manufactured and homologated

for such use;

– never smoke when handling fuel;

– slowly open the fuel tank to allow the pres-

sure inside to decrease gradually;

– top up the tank with fuel in the open air, using

a funnel;

– add fuel before starting the engine. Never re-

move the fuel tank cap or add fuel while

the engine is running or when the engine

is hot;

– if you have spilt some fuel, do not attempt to

start the engine but move the machine away

from the area of spillage and avoid creating

any source of ignition until the fuel has eva-

porated and fuel vapours have dissipated;

– immediately clean up all traces of fuel spilt on

the machine or on the ground;

– never start the machine in the same place

you refilled it with fuel;

– make sure your clothing does not come into

contact with the fuel. If it does, change your

clothes before starting the engine;

– always put the tank and fuel container caps

back on and tighten well.

3) Replace faulty or damaged silencers.

4) Before using the machine, check its general

condition and in particular:

– the throttle trigger and the safety lever must

move freely, they must not need forcing and

should return automatically and rapidly back

to the neutral position;

– the throttle trigger must remain locked until

the safety lever is pressed;

– the engine stop switch must easily move from

one position to the other;

– the electric cables and in particular the spark

plug cable must be in perfect condition to

avoid the generation of any sparks, and the

cap must be correctly fitted on the spark plug;

– the machine handgrips and protection de-

vices must be clean and dry and well faste-

ned to the machine;

– the chain brake must be in perfect working

order;

– the bar and the chain must be fitted correctly;

– the chain must be tensioned correctly.

5) Before starting your work, make sure that all

the protection devices are correctly fitted.

C) OPERATION

1) Do not operate the engine in a confined space

where dangerous carbon monoxide fumes can

collect. Make sure air circulates when working in

pits, holes or similar.

2) Work only in daylight or good artificial light.

3) Assume a firm and well-balanced position:

– where possible, avoid working on wet, slip-

pery ground or in any case on uneven or

steep ground that does not guarantee stabi-

lity for the operator;

– avoid using unstable ladders or platforms;

– do not work with the machine above your

shoulders;

– never run, but walk carefully paying attention

to the lay of the land and any potential obst-

acles.

– avoid working alone or in an isolated place, in

case you have to find help after an accident.

4) Make sure the machine is securely locked

when you start the engine:

– start the motor in an area at least 3 metres

from where you refuelled;

– check that there are no persons in the vicinity

of the machine;

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko 636 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 17,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko 636 Manual

Product: