520608

AKO K 811 Manual

3
Zoom out
Zoom in
Previous page
1/12
Next page
3
Installation and Operating Instructions
Convector K 811, K 821
1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
• Use device for room heating within enclosed rooms only.
• Repairs and corrective measures may only be carried out by
a qualified technician.
• Disconnect the power supply in the event of fault (pull out
the device plug or switch off the fuse).
• Do not use this device next to the bathtub, shower,
washbasin or swimming pool.
• Do not cover the heating device with any objects;
fire hazard! The device carries the symbol shown
on the right, which indicates that the heating
device must under no circumstances be covered
with any objects.
• Observe the minimum clearances.
• Caution! The outer surfaces of the device, and in particular
the air outlet grid, become hot during operation.
• Children or persons who are not capable of operating the
device safely must not operate the heating device. Ensure
that children do not play with the device.
• Caution! Potential dangers can arise when the device
switches on automatically, e.g. devices which have been
covered or blocked by objects since they were last used can
cause fire.
• Do not operate the heating device in rooms where highly
flammable substances are used (e.g. solvents, etc.).
• Do not lay the connecting cable across the hot device.
• In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through
an external switching device, such as a timer, or connected
to a circuit that is regularly switched on and off by the utility.
2. Technical data
Heat output: 2000 W
Connection voltage: 1/N/PE~, 230 - 240 V, 50 Hz
Protection type: IP20
Protection class: I (with protective conductor)
Dimensions:
free-standing (W x H x D) 575 x 418 x 200 mm
wall-mounted (W x H x D) 575 x 345 x 120 mm
Weight: 3.5 kg (K 811), 4.1 kg (K 821)
3. Installation
The heating device may only be installed as shown, i.e. on a
horizontal, even surface. Using it on deep-pile carpets is not
permitted. Please use caution when installing it in front of
flammable objects. Installation below a wall socket is not
permissible. Minimum clearances must be observed.
In addition, a minimum clearance of 500 mm between
flammable objects e.g. curtains, towels or heat-sensitive
plastics and the front of the unit must be maintained.
Installation of the supporting feet
Do not use the heating device without the feet being fitted.
The two mounting screws for
the supporting feet (A) are
located on the bottom of the
device. Loosen the mounting
screws.
Engage the supporting feet as
shown in the illustration and
tighten the screws.
Wall mounting
The device plug must be accessible after installation.
The heating device must be aligned horizontally and installed
on a vertical wall (see illustration).
Make sure that the inflow and outflow of air at the top and
bottom of the device are unimpeded
.
Install the device in such a manner that the controls cannot be
touched by a person in the bathtub or under the shower.
It is not permissible to install the device in protection zones as
defined in VDE 0100 part 701.
The wall brackets (B) attached to the bottom of the device must
be used.
- Drill mounting holes for the two upper wall brackets 358 mm
apart and insert dowels.
- Attach the upper wall brackets by tightening the screws and
hook the heating device on.
- Insert the third wall bracket into the lower back panel slot.
- Check the horizontal alignment of the heating device and
mark the hole for the lower wall bracket.
- Remove the heating device, drill mounting hole for the lower
wall bracket and insert dowel.
- Hook the heating device back onto the upper wall brackets
and screw the lower wall bracket to the wall.
EN
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AKO K 811 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AKO K 811 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info