520584

AKO BY 801 S Manual

3
Zoom out
Zoom in
Previous page
1/12
Next page
3
Installation and Operating Instructions
Infrared radiator BY 801 S
EN
1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
• The device must not be used in industrial areas, and must
only be used within enclosed rooms.
• The device may only be installed and repaired by a qualified
electrician in accordance with the applicable safety
regulations.
• Disconnect from the power supply in the event of a fault.
• Do not cover the heating device with any objects - fire
hazard!
• Observe the minimum clearances.
• Caution! The outer surfaces of the device are
hot during operation.
• Do not leave the heating device unattended when in use.
This applies particularly with small children or persons with
impaired health who are not able to vacate the radiation
area or the room when the temperature reaches an
excessive level.
• Children or persons who are not capable of operating the
device safely must not operate the heating device. Ensure
that children do not play with the device.
• Do not operate the heating device in rooms where highly
inflammable substances are used (e.g. solvents, etc.).
2. Minimum Clearances, Notes on Installation
• The minimum clearances must be observed.
A minimum clearance of 1 metre must be observed within
the radiation area.
• Inflammable objects must not be placed in the radiation area
of the heating device.
• The heating device must be aligned horizontally and
installed on a vertical wall (see illustration).
The device must be installed at a minimum height of 1.8
metres.
• It is not permissible to install the device vertically or on the
ceiling.
• The protection areas defined in VDE 0100 Part 701 must be
observed during installation.
• Do not place the device directly below a wall socket.
• Install the device in such a manner that it cannot be touched
by a person in the bathtub or under the shower.
• The device plug must be accessible after installation.
• Installation on wooden walls is permissble.
• Due to the heat radiation of the device, the surface on which
the device is installed can darken in colour.
Remove transport fastening
Only plug in the heater after installation.
- Loosen the front grill screws (A) and remove the front grill.
- Remove the transport fastenings (B) from the heating
element.
- Re-attach the front grill.
Wall Mounting
To achieve the stipulated minimum installation height of
1.8 metres, the mounting holes for the wall holder must be
drilled at a height of 1.9 metres.
- Loosen the screw on the cover of the wall holder and
remove the cover.
- Fold the radiator forward.
- Mark and drill the mounting holes on a vertical wall and
insert dowels.
- Insert spacers with screws into the openings of the wall
holder and screw the device into place.
3. Electrical Connection
Do not lay the connection cable in the radiation area and on hot
surfaces of the heating device. The voltage specified on the
type plate must match the mains voltage.
Plug in the heater. The device plug must always be accessible.
If the power line of this device is damaged, it must be replaced
by the manufacturer or after-sales service, or else by a similarly
qualified person, in order to prevent risks.
A
A
B
B
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AKO BY 801 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AKO BY 801 S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info