630567
16
Zoom out
Zoom in
Previous page
1/52
Next page
14
Adjusting the Breath Sensor
The breath sensor translates the strength of your breath into
the volume and character of the note you’re playing. It’s
important to set the sensor’s sensitivity so it suits your style
of playing.
1. Set the “S” (Sensitivity) knob in the “BR” (Breath)
section to the center position, and then turn the “A”
(Adjust) knob clockwise. The “Breath” indicator should
light up on the PROGRAM / DATA DISPLAY. If you
turn the “A” (Adjust) knob counterclockwise, it should
go off.
Note: If the “Breath” indicator is lit, the EWI4000s will
produce sound. Be careful of the volume settings on
any connected equipment while adjusting the breath
sensor.
2. Turn the “A” (Adjust) knob slowly counterclockwise
from the position where the indicator is lighting up, and
set it to the position where the indicator goes off.
3. Blow into the MOUTHPIECE. The breath sensor is properly adjusted if the sound starts when you blow
(and stops when you stop blowing).
4. To adjust the “S” (Sense) knob for breath sensitivity, blow into the MOUTHPIECE with various breath
strengths to confirm that the output sound volume changes depending on your breath strength. To
change this setting, turn the “S” (Sense) knob. For greater sensitivity, turn the knob clockwise. For
less, turn it counterclockwise. At a higher sensitivity, you may have less available articulation but not
need to blow as hard. At a lower sensitivity, you will need to blow harder to produce a sound, but you
can be more expressive with it.
Note: After adjusting the S (Sense) knob, you need to adjust the A (Adjust) knob again.
Adjusting the Pitch Bend Sensors
This section explains how to adjust the sensors for the Pitch
Bend Up and Down functions and sets the width of these
bends.
1. Set the “W” (Width) knob in the “PB” (Pitch Bend)
section to the right-most (fully clockwise) position.
2. While touching your thumb only to the GROUNDING
PLATE (without touching the PITCH BEND UP PLATE
or PITCH BEND DOWN PLATE), adjust the “A”
(Adjust) knob in the “PB” (Pitch Bend) section so that
both the UP and DOWN indicators on the PROGRAM /
DATA DISPLAY turn off.
3. Play the EWI4000s and use the PITCH BEND UP
PLATE and PITCH BEND DOWN PLATE. The bend sensor is properly adjusted if a note’s pitch raises
or lowers (and the upper or lower indicator LED lights up) appropriately when you touch either of the
bend plates. If you still want to adjust the settings, experiment more with the “W” (Width) knob. The
range becomes narrower as you turn it counterclockwise (and wider as you turn it clockwise).
The overall change in pitch varies by how much of the plate your thumb is touching as well how it is touching
the plate. You’ll need to experiment with the bend plates and sensor adjustment for the best results.
Note: After adjusting the W (Width) knob, you will need to adjust the A (Adjust) knob again.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Akai EWI4000s at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Akai EWI4000s in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info