496591
5
Zoom out
Zoom in
Previous page
1/52
Next page
BEFORE OPERATION
SETTING THE CLOCK
l=
__-.
r-
POWER ~f=
o
~
i
,==+—-“”’!====4
[p
mj
-107–-
—.
-.,
k~A
\_____
—!
To turn the unit on
@
SHIFT
FUNCTION
Press one (ofthe function buttons (TAPE, TUNER, VI DEO/AUX,
CD)-The unit is turned on.
At this time, playback of the inserted disc begins, or the previously
tuned station is received (Direct Play Function).
The POWER button is also available to turn the unit on.
The disc compartment may open and close to reset the unit,
when the unit is turned on.
After use
Press the POWER button to turn off the power. The display
changes to the clock.
DEMO (Demonstration) mode
When the AC cord is connected for the first time, the display
window demonstrates the functions of the unit. When the power
is turned on, the DEMO display is overridden by the operation
display.
To cancel DEMO mode
Press the II SET button while the power is off. In this time, the
clock on the display flashes. Go to step 2 of the SETTING THE
CLOCK to set the clock,
To use the SHIFT button on the remote control
Buttons @ have two different functions. One of these functions
is indicated on the button, and the other on the plate above the
button.
To use the function on the button, simply press the button.
To use the function on the plate above the button, press the
button while pressing the SHIFT button.
To use the FUNCTION button on the remote control
The FUNCTION button substitutes for the function buttons
(TAPE/DE(;K 1/2, TUNER, VIDEO/AUX,CD) on the main unit.
Each time the FUNCTION button is pressed, the next function is
selected cyclically.
If the unii. is not going to be used for an extended period of
time, remove the batteries from the remote control to prevent
possible electrolyte leakage.
The remote control may not operate correctly when:
- The line of sight between the remote control and the remote
sensor inside the display window is exposed to intense light,
such as direct sunlight
- Other remote controls are used nearby (television, etc.)
Set the time as follows while the power is off.
1
2
3
4
5
Press the II SET button.
The hour flashes.
CLOCK
SHIFT
Press the
l<< DOWN or FFI UP button to
designate the hour.
Press the II SET button to set the hour.
The hour stops flashing and the minute starts flashing,
Press the l<< DOWN or FM UP button to
designate the minute.
Press the 11 SET button to set the minute and
complete setting.
The minute stops flashing on the display and the clock starts
from 00 second,
To
correct the current time
Press the POWER button to turn the unit off. Press the II SET
button and carry out steps 1 to 5 above.
To display the current time
Press the CLOCK button while pressing the SHIFT button on
the remote control. The clock is displayed for 4 seconds.
However, the time cannot be displayed during recording.
To switch to the 24-hour standard
Press the CLOCK button while pressing the SHIFT button on
the remote control and then press the
button within 4 seconds.
Repeat the same procedure to restore the 12-hour standard.
If the clock display flashes
This is caused by a power interruption. The current time needs
to be reset.
If power is interrupted, all settings stored in memory after
purchase may need to be reset.
ENGLISH ~
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa NSX-V2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa NSX-V2100 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info