496555
71
Zoom out
Zoom in
Previous page
1/80
Next page
If the system does not seem to operate as it should, after re-reading these operating instructions carefully, check the chart below:
P.’.
Power does not turn on.
-,
There is no sound.
The indicators in the
display go out or the power
3
$-- is turned off soon after it is
s
turned on.
&
Sound comes from only
one speaker.
The display is strange,
The Dower cord is not connected DroDerlv,
Correct the connections.
I
The flat cables are not connected properly.
An incorrect function button was oressed.
Correct the connection,
I
Press a function button to select the correct inwt.
I
There is a bad connection between units.
Correct the connection.
J
There isashort circuit inthe speaker jack.
The breaker tripped because ofaconnection toalow-
impedance speaker,
Disconnect the ACpowercord, correct thecondition,
including speaker connections, and then connect the
power again, Turn on the power by pressing the
POWER button.
If the clock display is flashing, set the clock again
(page 13)..
Correct the speaker connection.
A speaker is disconnected.
The microprocessor has been electronically affected.
With the MEMORY button pressed down, turn the
power back on. (All stored settings will be erased
from the system.)
The antenna is not connected properly.
The station is not correctlv tuned,
Check the antenna connection,
Correct the tunina.
The signal is too weak.
The system is picking up outside noise.
Install an outside antenna.
Change the location or direction of the antenna.
Turn the system to a different orientation.
Move the system away from other electrical
appliances, such as a TV, fluorescent lights, or
move the appliances.
There is multi-path distortion.
Change the orientation of the antenna.
Replace the antenna with one that has the correct
orientation
I
The ta~e does not run. Press II PAUSE to release the ~ause
Deck 2 is Daused,
I
The sound is off-balance.
High sounds are too loud.
The head is ditty.
The Dolby NR mode is set differently from when the
recordina was done.
Clean the head.
Reset the Dolby NR.
,
There are no high
frequencies,
A tape recorded without Dolby NR is being played back in
the Dolbv NR
mode.
Turn off the Dolby NR.
The head is dirty, Clean the head.
~”] There is no recording. The erasure prevention tab on the tape has been removed. Cover the erasure prevention hole with cellophane
taoe.
There is an incorrect connection.
Correct the connection.
The head is dirtv. Clean the head oro~erlv
The erase head is dirty.
The vocal fader is on.
Clean the erase head.
Press the KARAOKE button to turn it off.
The disc is not set correctly.
The disc is dirtv,
Set the disc with the label facing up.
Clean the disc.
Moisture has condensed.
Leave the system with the power on for some time.
Playback becomes possible.
Press the - PLAY/PAUSE button to release the ~ause.Plavback is ~aused.
Press the KARAOKE button to turn it off.
The vocal fader is on.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa NSX-D939 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa NSX-D939 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 29,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info