496518
50
Zoom out
Zoom in
Previous page
1/60
Next page
If the unit fails to perform as it is supposed to, by following this operation manual, please check it carefully in accordance with the chart below:
11
‘“*C There is no sound.
, q?
The power cord is not connected properly.
Ill
An incorrect function selector button is pressed.
~,
&&Bf,
m,.
~~h-
There is a bad connection between systems.
Ml,&
II
~.m s
a
Excessive voltage was applied to a speaker jack,
.; *
which tripped the amplifier’s voltage-protection
breaker.
There is no sound and no
There is a shorl circuit in the speaker jack.
~a indicators are lit in the display
I
The breaker tripped because of connection to a low-
impedance speaker.
##l Sound comes from only one
I
Onespeakeris disconnected.
constant, wavelike static, I
The antenna is not connected properly.
U!M
I * The receiver is not correctlv tuned.
* The signal is too weak. -
c The system picks up outside noise.
The soun”d is distorted.
= There is multipath distortion.
p,
~sl The tape does not run.
Deck 2 is on pause.
rl
‘“? The sound is off-balance.
@
The playback head is dirty.
,##” High sounds are too loud.
The DOLBY NR mode is set differently from when
M%{
I the recordina was done
p
*-&j
;; There are no high sounds.
A non-Dolby NR tape is being played back in that
m
mode.
~(~g
I The Edavback head is dirtv.
1
Recording is impossible.
* The erasure-prevention tab on the tape has been
I broken.
~~q
I There is an incorrect connection.
~~f I The recording head is dirty.
Erasure is impossible.
The erasure head is dirty.
The disc is incorrectly inserted.
Rmm
,.
I
]
The disc is dirty.
Bma
I
14
‘!
& j
. There is condensation on the disc.
,Z,
The player is on pause.
/,,,,,.
&& The output sound is not stereo.
J&
The VOCAL FADER is turned on,
Correct the connection.
Press the function selector button to select the
correct input.
Correct the connection.
Disconnect the power cord, correct the condition,
including speaker connections, and connect the
power cord again.
. Disconnect the power cord, correct the condition,
including speaker connections, and connect the
power cord a~ain.
Correct the speaker connection.
Check the antenna connection.
Correct the tuning.
Install an outside antenna,
Change the location or direction of the antenna.
Turn the system to a different orientation.
Move the system away from other electrical
appliances, like a TV or fluorescent lights, or move
the appliances.
Change the orientation of the antenna.
Replace the antenna with one that has the correct
orientation.
Press 11and release t)ause.
Clean the head.
Reset DOLBY NR to the same setting as when the
recording was made.
Turn off DOLBY NR.
Clean the head.
c Cover the erasure-prevention hole well with tape.
Correct the connection.
Clean the head.
Clean the erasure head.
Insert the disc with the label facina uo
Clean the disc.
Wait about an hour and try again.
Press 11PAUSE to release ~ause.
Turn off the VOCAL FADER.
50
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa NSX-332 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa NSX-332 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 30,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info