157626
10
Zoom out
Zoom in
Previous page
1/40
Next page
SETTING THE CLOCK
m—
-m
When the AC cord is connected for the first time, the time on the
display flashes.
Set the time as follows
while the power is off.
1
2
3
4
5
Press the SET button.
The hour flashes.
Press the 1<+ or >[ button to designate
hour.
Press the SET button to set the hour.
The hour stops flashing and the minute starts flashing.
Press the l++ or >1 button to designate
minute.
the
the
Press the SET button to set the minute and
complete setting.
The minute stops flashing on the display and the clock starts
from 00 seconds.
To correct the current time
Press the POWER button to turn the unit off and press the SET
button. Then, carry out steps 1 to 5 above.
To display the current time
Keep the
button pressed until the clock is displayed. The
time is displayed for 4 seconds,
To switch to the 24-hour standard
While the power is on, keep the
button pressed until the clock
is displayed and then press the REPEAT button within 4 seconds.
Repeat the same procedure to restore the 12-hour standard.
If the clock display flashes while the power is off
This is caused by a power interruption, The current time needs
to be reset,
If power is interrupted for more than approximately 12 hours, all
settings stored in memory after purchase need to be reset.
SETTING THE TIMER
u
<—
c).
.——----
1
The unit can be turned on at a specified time with the built-in
timer.
Preparation
Make sure the clock is set correctly.
1
2
3
4
5
Press the TIMER button on the remote control to
display 0, and press the SET button within z
seconds.
O
is displayed, and the hour flashes.
m
If you do not press the SET button within 2 seconds, another
operation may start.
Designate the hour of the timer-on time by
pressing the 1<+ or FPI button, and press the
SET button. Repeat to designate the minute of
the timer-on time.
Select the duration for the timer-activated period
with the l-or >1 button and press the SET
button.
The duration for the timer-activated period can be set between
5 and 240 minutes in 5-minute steps.
Prepare the source.
To listen to a CD, press the -11 button and load the disc.
To listen to the radio, press the BAND button and tune in to
a station.
Press the POWER button to turn the unit off after
adjusting the volume.
@
remains on the display after the power is turned off (timer
standby mode).
When the timer-on time is reached, the unit turns on and
begins play with the selected source.
You cannot set the volume level to 21 or higher,
9 ENGLISH
Downloaded from www.Manualslib.com manuals search engine
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa lcx 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa lcx 150 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 6,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info