496437
12
Zoom out
Zoom in
Previous page
1/98
Next page
12
ENGLISH
SELECTION OF AUDIO/VIDEO
SOURCE
1 Select the program source.
Turn FUNCTION or press TAPE MONITOR. The selected
function indicator lights in red.
To listen to or watch The indicator in red
Tape TAPE MONITOR
Radio TUNER
Record PHONO
Compact disc CD
Television, etc. AUX
Video VIDEO 1/DVD/MD,
VIDEO 2/LD/TV, VIDEO 3
LD or Cable TV VIDEO 2/LD/TV
MD or DVD VIDEO 1/DVD/MD
The function to be selected (except PHONO) depends on the
equipment connected to the input terminals on the rear panel
of the unit.
To select with the remote control
Press TAPE MONITOR or FUNCTION repeatedly.
NOTE
When using a turntable with a built-in equalizer amplifier, set
the switch of the equalizer amplifier to off. See the instructions
of the turntable for further information.
2 Start the selected program source.
3 Adjust the sound.
About the video source to the monitor or TV
The selected video source is indicated on the display and the
video signal is output through the MONITOR VIDEO OUT jack to
the TV.
BASIC OPERATIONS
To select the video source
1 Turn FUNCTION to select PHONO, CD or AUX.
2 Press ENTER to display VIDEO 1.
3 Turn MULTI JOG to select VIDEO 2 or VIDEO 3.
To change a displayed name for the VIDEO 1
and VIDEO 2 function
When the VIDEO 1 function is selected, VIDEO 1 is displayed
initially. It can be changed to DVD or MD.
Press BAND/DIGITAL/ANALOG while pressing ENTER,
then
release ENTER first.
The displayed name for the VIDEO 2 function can be changed to
VIDEO 2, LD or TV; while the VIDEO 2 function is selected, press
BAND/DIGITAL/ANALOG while pressing ENTER,
then release
ENTER first.
To select ANALOG or DIGITAL (auto) mode
of the VIDEO 1 or VIDEO 2 function
Press BAND/DIGITAL/ANALOG when the VIDEO 1 or VIDEO 2
function is selected. The selected mode ANALOG or DIGITAL
appears on the display.
In DIGITAL mode: Equipment connected to the VIDEO 1
OPTICAL IN terminal is selected as a source for the VIDEO 1
function, and equipment connected to the VIDEO 2 COAXIAL IN
terminal for the VIDEO 2 function.
In ANALOG mode: Equipment connected to the VIDEO 1/DVD/
MD IN terminals is selected as a source for the VIDEO 1 function,
and equipment connected to the VIDEO 2/LD/TV terminals for
the VIDEO 2 function.
NOTE
DIGITAL mode changes to ANALOG, when pressing TAPE
MONITOR.
When the OVER LEVEL indicator lights up
The unit is equipped with the OVER LEVEL indicator. When input
analog signals from the connected equipment are too high to
accept, the indicator lights up. In this case, adjust the input level
as mentioned below so that the indicator disappears.
To adjust the sound level of the connected source
The input sensitivity level of each function can be adjusted (except
the TUNER, VIDEO 1 (DIGITAL) and VIDEO 2 (DIGITAL)
functions).
When the sound level of the connected source is higher than
that of the TUNER, adjust it as follows.
1 Select the function to be adjusted.
Turn FUNCTION or press TAPE MONITOR and play the
source. Be sure to turn off the source direct function.
2 Press
MM
MM
Mtwice to lower the level.
To restore, press N twice so that 0 dB is displayed.
V1: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3
Selected video source
BASIC OPERATIONS
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa AV-D58 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa AV-D58 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info