28960

Airtronics RD6000sport Manual

11
Zoom out
Zoom in
Previous page
1/63
Next page
11
TRAINER SYSTEM
The Trainer system in the RD6000 Sport transmitter allows you to connect any two Airtronics RD6000
Sport together for the purpose of training a new pilot. You can also connect the RD6000 Sport to either an
RD6000 Super, RD6000, VG 400, VG 600, Radiant or Vanguard PPM unit. The Trainer cord to use is the
ATX Part # 97100. The RD6000 Sport is NOT compatible with Infinity 660 or Quasar units.
In actual use, one of the two transmitters will serve as the Master and the second transmitter will serve as
the Trainer. The Master transmitter is held by the instructing pilot, AND IS THE TRANSMITTER THAT
MUST MATCH THE RECEIVER FREQUENCY INSTALLED IN THE MODEL! The trainer transmitter is
held by the learning pilot, and does not need to be on the same frequency as the model. The frequency of
the Trainer transmitter is unimportant because the switch of the trainer transmitter is
NOT turned on during
instructional flying. Normally during training, the instructor takes the model off and flies it to a reasonable
altitude. While the Master/Trainer switch on the Instructors transmitter is left in its OFF position, the
Master transmitter will have full control of the model. When the instructor is ready to begin training, he
presses and holds the spring loaded switch on his transmitter which transfers control to the student.
(As long as the instructor holds his Trainer switch in the ON position, the model will respond to the com-
mands of the Trainer transmitter sticks allowing the pupil to fly the model. It is not necessary for the student
to hold the trainer switch on the Trainer transmitter.)
When the instructor ceases to stop training, or if he feels that the student is in a situation that endangers the
model, the instructor can release the spring loaded switch and control of the model will immediately return to
the Master transmitter. To use the Trainer system, you must plug the appropriate Trainer cable into the back
of both the Master and the Trainer transmitters. Turn on the Master transmitter and the Model. The cable will
energize the encoder section of the Trainer transmitter. Once you have verified that both the Master and the
Trainer transmitters will control the model when the spring loaded switch in the appropriate position you are
ready to start training.
NOTE:
Both transmitters must be programmed identically for the trainer system to function properly. All servos must
operate in the same direction, centering, end points, and other settings such as type of Modulation must be
identical.
Trainer Switch
(Spring Loaded)
Master Transmitter
Trainer Transmitter
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airtronics RD6000sport at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airtronics RD6000sport in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info