593955

Airpress H260-10 Manual

28
Zoom out
Zoom in
Previous page
1/52
Next page
26
5.0 OPERATION
Compressor with direct drive:
1. The automatically operating compressor will stop at a pressure of 8 - 10 bar.
When air is used again and the pressure in the tank falls to 6 - 8 bar, the
compressor will start again.
2. Most pneumatic machines are suitable for an operating pressure of about 7 bar.
For some applications this pressure is even lower. To be able to set the right
pressure, the compressor is provided with a reducing valve (b). This valve can
set the pressure of the air receiver (of course never higher than the pressure in
the air receiver).
3. The setting of the reducing valve is done as follows:
a. Pull up the button (b) of the pressure switch.
b. Switch the button to set the right pressure (to the left to lower the pressure, to
the right to increase it).
c. Press button down again after setting to lock the button.
4. Two extra plugs (j) are fitted to the tank, which can be used to get an extra
pressure connection.
The points mentioned above are not valid for the H 85. The compressor H 85 is
executed with an adjustable safety valve and runs continuously.
Compressor with V-belt drive:
1. Check if the pressure switch (a) is turned off. Connect electricity. Turn on the
pressure switch. If the air pressure in the air tank is lower than the 'switch on
pressure', the compressor will turn itself on, until maximum pressure has been
reached. Is the pressure in the tank higher than the 'switch on pressure' the
machine will not start, but will be stand by to start when the pressure drops to
low.
2. When switching of the compressor, first switch the pressure switch to "0" before
turning off the electricity. The pressure switch takes the pressure off the air
circuit, so that the compressor can run freely when it starts again. This prevents
damage to the motor.
3. The electric motor of your compressor is protected against burning by a thermal
overload device. This device turns off the motor automatically, if the motor should
get overloaded, or if one phase should fall out. By pressing the reset button on
the thermal overload device after a short time, the compressor will function again.
ATTENTION !
Checking the oil level and refreshing the oil does not apply to the oil free
models HLO 110/6, HLO 200/25, HLO 215/25, HLO 300/50 and HLO 300/100.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airpress H260-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airpress H260-10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info