Manual Airpress 36844 - HL 375-100 (page 21 of 48) (English, German, Dutch, French, Spanish)

593982

Zoom out

Zoom in

1/48

3.2 AIR CONNECTION

Best use for connection of the compressor to an air circuit a flexible hose, to

isolate fibrations from the machine. The coupling No 6 is an Orion/Airpress quick

coupling.

4.0 FIRST USE

1. Check if the instructions mentioned above have been executed.

2. On delivery the compressor mostly is not filled with oil. Fill about 0,5 litres

compressor oil until the red circle on the oil inspection glas (12).

3. Install the oil filler cap (13) on the crank case lid (first remove the synthetic

plug).

4. Avoid the use of extension cables. If you use them, unroll them completely and

use cables of sufficient capacity. Tabel for extension cables:

0 - 10 meter: 3 x 1,5 mm

and 10 - 25 meter: 3 x 2,5 mm

5. Check tension on the V-belt (14). At the right tension the V-belt can easily be

turned by hand approximately 45 degrees. If necessary, improve tension. See

chapter 6.0 point 5. For daily operation of the compressor, see chapter 5.0.

• Switch on the compressor by means of pulling the pressure switch (4).

• The compressor will now operate, unless the air receiver is still under pressure

(pressure gauge 8).

• Switch the machine, during operation, exclusively off by means of pushing the

button on the automatic pressure switch (4); the pressure circuit will be vented

and the compressor can start again uncharged.

5.0 OPERATION

1. Check if the pressure switch is turned off. Connect electricity. Turn on the

pressure switch. If the air pressure in the air tank is lower than the 'switch on

pressure', the compressor will turn itself on, until maximum pressure has been

reached. Is the pressure in the tank higher than the 'switch on pressure' the

machine will not start, but will be stand by to start when the pressure drops to

low.

2. When switching of the compressor, first switch the pressure switch to "0" before

turning off the electricity. The pressure switch takes the pressure off the air

circuit, so that the compressor can run freely when it starts again. This prevents

damage to the motor.

3. The electric motor of your compressor is protected against burning by a the-

rmal overload device. This device turns off the motor automatically, if the motor

should get overloaded, or if one phase should fall out. By pressing the reset

button on the thermal overload device after a short time, the compressor will

function again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Airpress 36844 - HL 375-100 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Airpress 36844 - HL 375-100 Manual

Product: