593971
18
Zoom out
Zoom in
Previous page
1/44
Next page
16
a qualified electrician.
Make sure that the machine and the cable never come in contact with water.
Treat the power cable with care. Do not attempt to move the machine by pulling
the cable. Do not yank the cable to unplug it; keep the cable away from excessive
heat, oil and sharp objects.
Never leave the machine unattended with the power supply "on". Also
disconnect the power cable when:
- you leave the machine, even for a short time
- not in use
- carrying out maintenance work
- changing attachment or moving the machine.
WARNING: the warnings, cautions and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the
operator.
Only those persons who are aware of how to use the compressor by having read
this manual, should use the machine. Injudicious use may cause danger.
Danger plates (see page 32)
The plates fitted on the compressor unit are part of the machine; they have been
applied for safety purposes and must not be removed or spoiled for any reason.
3.0 PLACING
The compressor should be placed in such way that all points, destined to carry it will
really do so. Take also care of a horizontal position. The engine should get sufficient
cooling air; so never cover the ventilating openings.
Place the compressor in a cool dustfree space. Never place the compressor in a
room where will be sprayed. Paint spray will clog the air filter and will also deposit on
the compressor.
Mind that the drain tap for condensation water (K) will always remain attainable. We
suggest to leave a space of approximately 30 cm for ventilation and maintenance.
Notice: Insufficient air supply, too high temperature and fouling of the air filter
reduce the efficiency of the compressor considerably.
3.1 ELECTRIC CONNECTION
At the factory the machine is already fully equipped with cables. The machine now
has to be connected to your own electricity supply. Connect the machine to a
separate group. Beware that voltage and amperage of your electric circuit meet the
needs of the motor. Use only cables with the right diameter. The factory suggests to
use cables of at least 2.5 qmm.
Before first use first read chapters 3.2 and 4.0.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airpress 36740-1 - HLO 215 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airpress 36740-1 - HLO 215 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info