Manual Airpress 36523 (page 29 of 52) (English, German, Dutch, French)

593936

Zoom out

Zoom in

1/52

4.0 FIRST USE

1 Check if the instructions mentioned above have been executed.

2 Check the oil level of the compressor. The oil level has to be on the red dot on

the inspection glass (8). Possibly oil has been lost during transport. Fill if

necessary with AIRPRESS compressor oil through desaeration motor case/oil

refill cap (11).

3 Check tension on the V-belt. At the right tension the V-belt can easily be turned

by hand approximately 45 degrees. If necessary improve tension (see chapter

5.0 point 5).

4 Let the compressor run for a short while so you can check if the turning direction

is correct (see arrow on belt protector (3)). If the motor runs in the wrong direc-

tion, switch two phases of the electric plug. Disconnect electricity!

5 For daily operation of the compressor see chapter 5.0.

6 After 20 working hours fix the head bolts. See below:

TIGHTENING MOMENTS BLACK PUMPS BUILD ON:

K 100-300 t/m K 300-600 head bolts: 27 Nm. (from 2002)

K 300-700 t/m K 500-700 S head bolts: 55 Nm. (from 2002)

K 500-1000 t/m K 500-1500 S head bolts: 94 Nm. (from 2002)

5.0 OPERATION

Types with thermal overload device:

K 100-300 & K 100-300/M K 300-600

K 100-450 K 300-700 S*1

K 200-450 K 200-600

Types with star-delta switch:

K 300-700 S*2 K 500-1000 Super

K 500-700 Super K 500-1500 Super

Check if the pressure switch is turned off. Connect electricity. Turn on the

pressure switch. If the air pressure in the air tank is lower than the `switch on

pressure', the compressor will turn itself on, until maximum pressure has been

reached. Is the pressure in the tank higher than the `switch on pressure' the

machine will not start, but will be stand by to start when the pressure drops too

low.

When switching of the compressor, first switch the pressure switch to "0" before

turning off the electricity. The pressure switch takes the pressure off the

compressed air circuit, so that the compressor can run freely when it starts again.

This prevents damage to the motor.

The electric motor of your compressor is protected against burning by a thermal

overload device. This device turns off the motor automatically, if the motor should

get overloaded, or if one phase should fall out. By pressing the reset button on

the thermal overload device after a short time, the compressor will function again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Airpress 36523 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Airpress 36523 Manual

Product: