594017

Airpress 36503 Manual

30
Zoom out
Zoom in
Previous page
1/56
Next page
28
machine cool down after use.
• After each use the tank must be vented and the moisture collected in the tank
must be bled. Not bleeding the tank can lead to leakage and may cause a
dangerous situation.
• Check that the electric circuit is adequately protected and that it corresponds
with the power, voltage and frequency of the motor. Check that there is a
ground connection and a regulation differential switch upstream.
• Use cables with an adequate section and avoid use of free and inadequately
insulated connections.
• Never open the pushbutton box on the motor. Should this be necessary,
contact a qualified electrician.
• Make sure that the machine and the cable never come in contact with water.
• Treat the power cable with care. Do not attempt to move the machine by pulling
the cable. Do not yank the cable to unplug it; keep the cable away from
excessive heat, oil and sharp objects.
• Never leave the machine unattended with the power supply "on". Also
disconnect the power cable when:
- you leave the machine, even for a short time
- not in use
- carrying out maintenance work
- changing attachment or moving the machine.
• WARNING: the warnings, cautions and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be
supplied by the operator.
• Only those persons who are aware of how to use the compressor by having
read this manual, should use the machine. Injudicious use may cause danger.
Danger plates (page 49)
The plates fitted on the compressor unit are part of the machine; they have been
applied for safety purposes and must not be removed or spoiled for any reason.
3.0 PLACING
The AIRPRESS compressor is equiped with wheels and a pull bow (L models with
carrying handle) making the machine very mobile. When placing the machine, take
care of a horizontal position. If not placed horizontal, severe damage may occur
due to lack of lubrication. The engine should get sufficient cooling air, so never
cover the ventilation openings.
If the compressor should get a permanent place, place it in a dustfree room.
Never place the compressor in a room where will be sprayed. A paint spray clogs
namely the airfilter and also deposits on the compressor. Mind that the draintap for
condensation water and the level gauge will always remain attainable. We suggest
to leave a space of aproximately 30 cm for ventilation and maintenance.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airpress 36503 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airpress 36503 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info