534691
29
Zoom out
Zoom in
Previous page
1/43
Next page
Afinia H-Series 3D Printer User’s Manual
29
Model Removal
When the model has finished printing, the printer will beep, the nozzle and platform will stop
heating, and the printer platform will lower.
It is very strongly recommended that you never attempt to remove the finished model from the
platform while in the printer. If you do, you may bend the entire platform assembly so that it is no
longer perpendicular to the printer head or affect the platform leveling.
If your print surface is attached directly to the printer platform, detach the printer platform from the
printer by removing the 2 screws at the bottom of the platform before attempting to remove the
model.
If you are using any method that clips another surface to
the printer platform, simply remove the clips holding the
surface to the platform and remove the entire surface.
Removal from FR-4 (Perf) Board
Gently slide a spatula or chisel under the model and
slowly wiggle it back and forth to lift the support
material from the print surface.
Remember to use gloves as the board and model may
still be hot and to prevent injury from any tool being
used to help release the model from the FR-4 Board.
Removal from Borofloat Glass
After removing the glass from the printer platform, allow the glass to cool completely. As the
glass cools, you may hear audible cracking sounds – this is the ABS film contracting and
detaching from the surface of the glass.
If the model does not release completely from the surface of the glass, spray a small amount of an
ammonia-based window cleaner onto the surface of the glass near the edge of the model. After a
few moments, the model should release.
With the glass surface, you will need to reapply the ABS film after removing each print job.
TIP: Depending on the platform preparation method you are using, the model may be easier to
remove from the printer when it is still hot. If you want to heat the platform before removing
your model, use the Table Heat option from the 3D Print menu.
CAUTION: It is strongly recommended that you do not attempt to remove the
model from the platform while the platform is still attached to the printer. Doing
so may damage the printer or affect the platform level and nozzle height
calibration.
GLOVES: It is recommended that gloves be worn as the platform may still be hot
and to prevent injury from any tool being used to help remove the model from the
platform.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Afinia H-Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Afinia H-Series in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info