782361
33
Zoom out
Zoom in
Previous page
1/136
Next page
SCOOPY+ S - User Manual
27
2.4. Auxiliary transmission functions
The main function of the SCOOPY+ S is the transmission of one or two audio channels, but it also provides
auxiliary functions for transmitting additional data, inside the same stream (or, more generally, the
same session).
Exchange of binary data with the remote codec during transmission: sending and receiving two
Boolean states "INFO1" and "INFO2". On the receiving direction these states are shown on the
front panel, and can close relay contacts (GPO), found on the "EXTENSION" connector of the
SCOOPY+ S. The transmitted states can be set by GPI contacts on this same connector, or
alternatively by keys on the front panel. A typical application is the transmission of an "On Air"
signal. See operation details in 3.2.1 and 4.4.7. This feature is not available through a mobile
voice link.
Exchange of additional "INFOn" states, up to 4 signals. Using these is possible if complementing
the SCOOPY+ S with a GPIO extension box, available as an accessory. This box provides 4 GPIO
isolated inputs and outputs. See operation details in 4.4.7. Only an IP network (Ethernet or
mobile) can support such additional transmission.
Receiving SMS from the mobile network, available when the "HD-4G Mobile" option is installed
and as soon as the unit is registered on a mobile network. The PIN code of the SIM card must be
entered beforehand. When receiving an SMS (sent to the SIM card's subscriber number), the
message is displayed directly on the front panel, and it can be read as well from a page of the
embedded html server of the unit. This function is independent from the transmission link(s).
"In-band" exchange of information ("RC data" in the table below): this function allows a remote
unit to remote control the SCOOPY+ S via a running ISDN link. This control mode uses the
dedicated AARC protocol. This additional transmission exists only over ISDN and excludes
INFO1/INFO2 exchanges).
These various features are only compatible with AETA products, because they are not inside the
scope of independent standards. Besides, for using them they must be activated on the remote unit
as well.
The availability of these functions depends mainly on the transmission network. The following table
summarizes the capabilities.
Table 5 Auxiliary functions depending on the network used
Besides, over ISDN links auxiliary data transmission is only available for the following coding algorithms:
G722-H242
MPEG Layer 2 with J52
4SB ADPCM
INFO1 / INFO2 INFO3 to INFO6
ISDN
IP
POTS
Mobile voice
Network
Transmission
SMS
RC
data
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeta Scoopy plus S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeta Scoopy plus S in the language / languages: English as an attachment in your email.

The manual is 5.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info