782361
15
Zoom out
Zoom in
Previous page
1/136
Next page
SCOOPY+ S - User Manual
9
Available audio coding algorithms
The audio coding algorithm can be selected depending on the required quality and the available
network bandwidth. The following algorithms are currently available:
Codec
Bit rate
(coding)
Bit rate
(total)1
Audio
bandwidth
Typical use, main features
G711
64 kbit/s
86 kbit/s
3 kHz
Voice, telephony
Compatible with IP phones
CELP
24 kbit/s
28.5 kbit/s
7 kHz
Suitable for high quality speech;
Low network bandwidth consumption
G722
64 kbit/s
86 kbit/s
7 kHz
High quality speech.
Compatible with some IP phones.
MPEG Layer II
64 to 256
kbit/s
73 to 275
kbit/s
Up to
20 kHz
Highest quality, suitable for speech and music
MPEG AAC-LC
16 to 256
kbit/s
30 to 277
kbit/s
Up to
20 kHz
Low bit rate, suitable for speech and music
MPEG HE-AAC and
HE-AAC v2
16 to 128
kbit/s
23 to 139
kbit/s
Up to
20 kHz
Very low bit rate, suitable for speech and music
4SB ADPCM
128 or 256
kbit/s
173 or 301
kbit/s
15 kHz
Low latency, suitable for speech and music
OPUS
12 to 256
kbit/s
28 to 272
kbit/s
Up to
20 kHz
Low bit rate and low latency, suitable for
speech and music
Linear L16/L20/L24
512 to 2304
kbit/s
592 to 2384
kbit/s
Up to
20 kHz
Best quality, very low latency
Table 2 Overview of algorithms available in IP mode
IP multicast mode
The multicast mode allows an encoder device to transmit an audio programme to several decoders by
sending a single encoded stream to a multicast group address. The link is unidirectional by nature. This
mode can be used on a local area network, and on larger private networks that can manage the
multicast mode. On the other hand, Internet cannot support this routing mode.
In this mode, the SCOOPY+ S uses the RTP protocol to manage the audio stream, like in the unicast mode,
but the SIP protocol is not applicable here; instead a proprietary signalling system is used. As the link is
unidirectional, the unit has to be set either as a "sender" in order to encode and transmit the audio
stream to the selected group address, or as a "receiver" to receive and decode such stream coming from
a "sender" device.
The audio coding algorithm can be selected with just the same capability as for the unicast mode
described above.
SIP and SDP protocols
The SIP protocol is a signalling protocol, used for IP connections, which allows the SCOOPY+ S to
interoperate with IP phones and other SIP compatible audio codecs, in a way similar to ISDN or POTS
connections. Details about the SIP protocols can be found in the annex (refer to 8.2, Overview of the SIP
protocol).
1 Informative value; higher than the "net" encoded audio bit rate because of the protocol overhead
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeta Scoopy plus S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeta Scoopy plus S in the language / languages: English as an attachment in your email.

The manual is 5.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info