587610
67
Zoom out
Zoom in
Previous page
1/184
Next page
67
EN
IMDCFJ. 12.05 6343841_03
Setting supplementary electric heater setpoint
Index - String
MIN
value
MAX
value
Parameter function
0°C 65°C
This parameter indicates the deviation from the heating setpoint, for switching off the electric heater (if
active) in supplementary mode; as shown in Fig.12 on the previous page (Parameter Sri).
Setting electric heater band in supplementary/replacement mode
Index - String
MIN
value
MAX
value
Parameter function
0°C 20°C
In supplementary mode, the temperature of the water in the system is checked before the unit is
switched on. If the temperature is less than/equal to the value calculated for the switch-on band, the
electric heater will be switched on and will operate as per the diagram on the previous page Fig.12.
The value of the switch-on band is calculated as follows: switch-on band = (Heating setpoint) -
(Parameter Sri) - (Parameter Bri); see Fig.12 on previous page;
In replacement mode, this parameter represents the band of deviation from the heating setpoint, within
which the heater will be activated or deactivated, as shown on the previous page Fig.13.
Setting outside air temperature threshold for supplementary mode
Index - String
MIN
value
MAX
value
Parameter function
-40°C 50°C
This parameter indicates the outside air temperature threshold, beneath which the heater is activated in
supplementary mode; as shown on the previous page, in Fig.11 Parameter tA1.
Setting outside air temperature threshold for replacement mode
Index - String
MIN
value
MAX
value
Parameter function
-40°C 50°C
This parameter indicates the outside air temperature threshold, beneath which the heater is activated in
replacement mode; as shown on the previous page, in [Fig.A] Parameter tA2.
Setting the band for air temperature
Index - String
MIN
value
MAX
value
Parameter function
0°C 20°C
This parameter indicates the band applied to the air temperature setpoints (tA1-tA2).
Parameters only visible in model set for
hot water production
Parameters only visible in models set for
hot domestic water production
Parameters only visible in the models with DCP installed
Parameters only visible in bicompressor models
Parameters only visible in the models with inverter compressor
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aermec MODUCONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aermec MODUCONTROL in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info