618082
7
Zoom out
Zoom in
Previous page
1/36
Next page
7
F11 OPERATING MANUAL
© 2002 Design, 2013 Doc. No. 12-7285-r01 (5/3/13)
Situation that will sound (1, 2, or 3) sets of (1 to 10) .125 second beeps -
Depth Alarms DA 1 to DA 6, if set On.
BACKLIGHT
To turn the Backlight On, press and release the Light button (< 2 seconds). The Backlight will remain On for the Duration time set (a
Set Utilities selection) unless you turn it Off during that time.
The Backlight will come On (even if set OFF) when alarms strike and remain On until turned Off or automatically after 10
seconds .
Pressing and releasing the Light button (< 2 seconds) while the Backlight is On will turn it Off.
Depressing the Light button for 2 seconds while the Backlight is On, will reset the timer and extend the On time to the full
Duration time set.
If the Light button is depressed for > 60 seconds, the Backlight will be disabled and not turn On until the button is released then
pressed/released again.
The Backlight will be disabled when there is a Low Battery condition, and be re enabled once the battery is replaced.
Extensive use of the Backlight reduces Battery use life.
Turning the Backlight Off when it is not being used will help extend Battery use life.
The Backlight does not operate when the unit is connected to a PC or Mac.
AUTO GLO
When Auto Glo (a Set Utilities selection) is set On, Backlight operation on the surface in Watch and FREE modes is controlled as
it normally would be by the Light button and Duration time set.
Upon entry into Dive mode, the Backlight activates (turns On) automatically and remains On throughout the full dive until entry
into Surface mode when the Backlight operation reverts to normal.
POWER SUPPLY
The F11 utilizes (1) 3 volt CR2450 Lithium Battery.
Battery voltage is checked every 2 minutes during operation while on the surface.
If voltage decreases to the Warning level (2.75 volts), the Battery icon will appear on the Watch Main Time and Free Surface
screens (Fig. 2a) as an indication that the Battery should be changed prior to commencing a series of dives.
If voltage decreases to the Alarm level (2.50 volts), the Battery icon will flash and operation will automatically revert to Watch
Main Time and only operate in Watch modes until the Battery becomes completely depleted.
Low Battery Warning/Alarm conditions are not displayed during Dive Modes.
If a Low Battery condition was not displayed prior to starting a Dive, and a Low Battery condition occurs during the dive, there
will be sufficient Battery power to maintain operation for the remainder of that dive. Upon surfacing, the graphics CHNG >>
BATT will alternate (Fig. 3), then operation will automatically revert to and remain in Watch Main Time until the Battery becomes
completely depleted.
Fig. 2 - LOW BATTERY
WARNING
a
Fig. 3 - LOW BATTERY
ALARM
Each display represents unique pieces of information. It is imperative that you understand the
formats, ranges, and values of the information represented to avoid any possible misunder-
standing that could result in error.
Understand which Time displays are represented as Minutes: Seconds and which are
Hours:Minutes.
You must also understand the icons, symbols, and alpha/numeric messages presented.
The Informational Displays are described in detail as the various operating modes they
appear in are presented throughout this manual.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeris F11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeris F11 in the language / languages: English as an attachment in your email.

The manual is 7,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info