618066

Aeris A300 XT Manual

46
Zoom out
Zoom in
Previous page
1/56
Next page
46
A300/A300 XT OPERATING MANUAL
© 2002 Design, 2012 Doc. No. 12-7255-r01 (5/14/12)
CARE AND CLEANING
Protect your unit from shock, excessive temperatures, exposure to chemicals, and tampering. Protect the lens against scratches
with a Instrument Lens Protector. Small scratches will naturally disappear underwater.
• Soak and rinse the unit in fresh water at the end of each day of diving, and check to ensure that the areas around the Low
Pressure (Depth) Sensor (Fig. 124a, 125a), PC Interface Data Port (Fig. 124b, 125b), and buttons are free of debris or
obstructions.
• To dissolve salt crystals, soak in lukewarm water or a slightly acidic bath (50% white vinegar, 50% fresh water). After
removal from the bath, place the unit under gently running fresh water and towel dry before storing.
• Transport your unit cool, dry, and protected.
INSPECTIONS AND SERVICE
Your A300/A300 XT should be inspected annually by an Authorized AERIS Dealer who will perform a factory prescribed func-
tion check and inspection for damage or wear. To keep the 2 year limited warranty in effect, this inspection must be completed
one year after purchase (+/- 30 days).
AERIS recommends that you continue to have an inspection performed every year to ensure it is working properly. The costs of
annual inspections, or inspections relating to water tight integrity, are not covered under the terms of the 2 year limited warranty.
To Obtain Service:
Take your unit to your local Authorized AERIS Dealer.
If required to return your unit to the factory:
• Obtain an RA (Return Authorization) number by contacting AERIS at 510/562-0500 or send an e-mail to service@
oceanicusa.com.
• Record all dive data in the Log and/or download the data stored in memory. All data will be erased during factory service.
• Package it using a protective cushioning material.
• Include a legible note stating the specific reason for return, your name, address, daytime phone number, serial number(s),
and a copy of your original sales receipt and Warranty Registration.
• Send freight prepaid and insured using a traceable method.
• Non-warranty service must be prepaid. COD is not accepted.
• Additional information is available on the AERIS web site diveaeris.com.
The procedures that follow must be closely adhered to.
Damage due to improper battery replacement is not covered by the product's warranty.
MODULE REMOVAL FROM BOOT (A300 only)
If necessary to remove the A300 module from a console, bend the rubber console boot back to expose the edge of the module.
If the boot is flexible enough to permit, you may bend it back far enough to scoop the module out with your finger. Otherwise, it
may be necessary to insert a blunt screwdriver until the tip rests just underneath the module.
DO NOT pry the module from the console! Slowly increase the pressure under the module by releasing the tension on the rub-
ber boot. The module will slide up the screwdriver and exit the console.
If the module is in a wrist boot, it will be necessary to peel the lips of the boot downward off the module while applying pressure
from underneath, working it out slowly.
When the battery is removed, settings and calculations for repetitive dives are retained in
the unit's memory while a new battery is installed.
BATTERY REPLACEMENT
The battery compartment should only be opened in a dry and clean environment with extreme care taken to prevent the entrance
of moisture or dust.
To prevent formation of moisture in the battery compartment, it is recommended that the battery be changed in an environment
equivalent to the local outdoor temperature and humidity (e.g., do not change the battery in an air conditioned environment, then
take it outside during a hot sunny day).
Battery Cover Removal
• Turn the unit, or module, over to expose the Battery Cover.
• While applying steady inward pressure on the center of the Battery Cover, rotate the Retaining Ring 10 degrees clockwise
using a cover tool (Fig. 126A) or by pressing against the upper tab of the Ring with a small blade screwdriver (Fig. 126B).
• Lift the Ring up and away from the housing, or turn the unit over to allow the Ring to drop out into your hand.
• Remove the transparent Battery Cover.
Battery Removal
• Remove the Retaining Bar located across the lower portion of the Battery (Fig. 127a).
• Remove the Cover O-ring. DO NOT use tools.
• Slide the Battery up and out of the battery compartment.
Fig. 124 - CASE BACK
(A300 module)
Fig. 126A - RING REMOVAL
(using cover tool)
Fig. 127 - RETAINING BAR
Fig. 125 - CASE BACK
(A300 XT console)
Fig. 126B - RING REMOVAL
(using screwdriver)
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeris A300 XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeris A300 XT in the language / languages: English as an attachment in your email.

The manual is 14,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info