464354
24
Zoom out
Zoom in
Previous page
1/62
Next page
26
For the Fitter
Model
WSP 2010
WSP 3010
WSP 4010
WSP 5010
WSP 6010
WSP 7010
6h heating element fitting set
(special accessory)
8h heating elements
(series)
Power
variants kW
Connection
variants
L1
N
L1
X1
3/N/PE ~ 50 Hz 400 V
1
L2L3123
100 % P
Nenn
(Serienverdrahtung)
L2L3
2
L1
L1
X1
3/N/PE ~ 50 Hz 400 V
L2L3123
91,6 % P
Nenn
L2L3N
3
L1
L1
X1
3/N/PE ~ 50 Hz 400 V
L2L3123
83,3 % P
Nenn
L2L3N
4
L1
L1
X1
3/PE ~ 50 Hz 400 V
L2L3123
75 % P
Nenn
L2L3
L1
N
L1
X1
1/N/PE ~ 50 Hz 230 V
5
L2L3123
100 % P
Nenn
2kW
2.2.2 Reducing the Output
By moving or removing bridges at the terminals, the connection rating, factory wired to 100 % can
be reduced by three levels (see the table).
The dimensioning of the line cross sections and the fusing should correspond to the maximum
possible output of the unit.
A single-phase connection may be made according to the "Technical connection conditions" of
the energy supply company only up to 2 kW (WSP 2010).
100 %
2.0
100 %
2.7
4.1
5.5
6.5
8.1
9.0
83.3 %
1.67
2.50
3.33
4.16
5.00
5.83
75 %
1.50
2.25
3.00
3.75
4.50
5.25
83.3 %
2.25
3.42
4.58
5.42
6.75
7.5
75 %
2.03
3.07
4.13
4.88
6.08
6.75
100 %
2.0
3.0
4.0
5.0
6.0
7.0
91.6 %
1.83
2.75
3.66
4.58
5.50
6.42
91.6 %
2.47
3.75
5.04
5.96
7.42
8.24
2.3 Rules and Regulations
Pay attention to the packing slip!
The national building and garage regulations must be taken into account.
The installation area must have a sufficient floor load capacity.
In case of doubt a building surveyor should be consulted (for weights of the storage heaters, see
Technical Data”).
The minimum distance from adjacent object surfaces must be kept (figs. 2 and 2a).
All electrical connection and installation work must be performed in accordance with the VDE
regulations (0100), the regulations of the electricity supply company responsible and the
pertinent national and regional regulations.
The device must be disconnectable from the mains at all poles by an supplementary device with a
disconnection distance of at least 3 mm. Contactors, fuses and similar can be connected for this.
A later increase in the output must be approved separately by the responsible electricity supply
company. Failure to notify the electricity supply company of the increase in the output
constitutes a breach of the electricity supply contract.
The operating equipment must be designed for the rated consumption of the units.
The unit’s rating plate must be observed!
The specified voltage must match the rated voltage.
The unit must be fixed to meet the VDE standing safety requirement.
75 % P
rated
100 % P
rated
(series wiring)
91.6 % P
rated
83.3 % P
rated
100 % P
rated
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WSP 4010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WSP 4010 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info