463284

AEG WSL 125 XS Manual

3
Zoom out
Zoom in
Previous page
1/23
Next page
!
2WSL 115 XS, WSL 125 X, WS 100 S, WS 115 S, WS 125 S
4 Before you use this tool
Always disconnect the plug from the socket
before carrying out any work on the machine.
4.1 Installation of Guard
Place guard on the gear neck (LEERER MERKER)
of the machine and then tighten screw
(LEERER MERKER).
The position of the guard can be adjusted to the
requirements of the work process. When making
this adjustment, take care to ensure that the
grinding disc can rotate freely.
4.2 Installation of Grinding Disc
Secure working spindle (LEERER MERKER) by
pressing spindle lock (LEERER MERKER).
Only press spindle lock when the machine is
turned off.
Mount back flange (LEERER MERKER), grinding
disc (LEERER MERKER) and flange nut
(LEERER MERKER) according to the illustration
and tighten flange nut with a pin–type spanner.
When the thickness of the disc is less than 5,5 mm
use the flange nut with the flat side against the
grinding disc.
4.3 Mains connection
Connect only to a single-phase AC current supply
and only to the mains voltage specified on the
rating plate. Connection to sockets without earth
protection is possible as the appliance features
protective insulation to DIN 57 740/ VDE 0740 and
CEE 20. Radio suppression complies with the
European standard EN 55014.
When fitting the plug, make sure that the brown
(live) wire of this appliance is connected to the plug
terminal marked L or coloured red, and the blue
(neutral) wire of this appliance is connected to the
plug terminal marked N or coloured black. Under no
circumstances must the wires of this appliance be
connected to the earth terminal of the plug marked
either E, with the earth symbol or coloured green or
green/yellow.
5 On-off switch
Intermittant Use
Switching on: Push forward on–off control
(LEERER MERKER) without pressure
Switching off: Release on–off control
Continuous Use
Switching on: Push forward on–off control
(LEERER MERKER) without pressure and then
press the button. On–off control will remain on.
Switching off: Press on–off control then release.
6 Operation
When grinding do not apply pressure to the
workpiece by bearing down on the machine but
move the grinding disc backward and forward over
the working surface.
Grinding
For best results with grinding discs, keep the disc at
an angle at least 30
o
to the working surface.
Overloading the machine during grinding operations
will harm the machine, reduce disc life and produce
inferior results.
Never use cutting discs for grinding operations.
Cutting
When cutting, avoid tilting the grinder away from
the cutting plane.
When cutting stone, the use of the guide
(LEERER MERKER is necessary.
For grinding larger areas use backing pad with
abrasive paper.
For removal of old paint and for derusting use steel
brush.
7 Accessories
The range of accessories with part numbers is
shown in our catalog.
8 Service
The ventilation slots of the machine must be kept
clear at all times.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not
been described, please contact one of our AEG
service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be
ordered. Please state the ten–digit No. as well as
the machine type printed on the label and order the
drawing at your local service agents or directly at:
Atlas Copco Elektrowerkzeuge GmbH,
Postfach 320, D–71361 Winnenden.
Modifications: Text, diagrams and data are correct at the time of
printing. In the interest of continuous improvement of our
products, technical specifications are subject to alteration without
prior notice.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WSL 125 XS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WSL 125 XS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info