Rated input .......................................................................................................................................2200 W ..................................2200 W
Rated speed ......................................................................................................................................8500 min
-1
.............................6600 min
-1
Grinding disk diameter........................................................................................................................180 mm .................................230 mm
Thread of work spindle .......................................................................................................................... M 14 ...................................... M 14
Weight according EPTA-Procedure 01/2003 .........................................................................................5,7 kg .....................................5,8 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A))
......................................................................................................94,3 dB (A) .............................94,3 dB (A)
Sound power level(K=3 dB(A)) ........................................................................................................105,3 dB (A) ...........................105,3 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding: vibration emission value a
h
......................................................................................7,6 m/s
2
.................................7,6 m/s
2
Uncertainty K .......................................................................................................................................1,5 m/s
2
.................................1,5 m/s
2
Disk sanding: vibration emission level a
h
............................................................................................15,9 m/s
2
...............................15,9 m/s
2
Uncertainty K .......................................................................................................................................1,5 m/s
2
.................................1,5 m/s
2
For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications, with dierent
accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running but not
actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the warnings
and instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, Wire Brushing or
Abrasive Cutting-O Operations:
a) This power tool is intended to function as a grinder, sander,
wire brush, or cut-o tool.Read all safety warnings, instructions,
illustrations and specications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
re and/or serious injury.
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power tool
was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specically designed and
recommended by the tool manufacturer. Just because the accessory
can be attached to your power tool, it does not assure safe operation.
d )The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool. Accessories running
faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your accessory must
be within the capacity rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or controlled.
f) The arbour size of wheels, anges, backing pads or any other
accessory must properly t the spindle of the power tool.
Accessories with arbour holes that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the
accessory such as abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush for loose or
cracked wires. If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystanders away
from the plane of the rotating accessory and run the power tool
at maximum noload speed for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and
shop apron capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of stopping ying debris
generated by various operations. The dust mask or respirator must be
capable of ltrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment. Fragments of workpiece or of a broken accessory may y
away and cause injury beyond immediate area of operation.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for AEG WS 2200-230 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of AEG WS 2200-230 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.
The manual is 8,22 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
