463260

AEG WS 2200-180 Manual

16
Zoom out
Zoom in
Previous page
1/112
Next page
15
English
GB
Appliances used at many dierent locations including open air should be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Sawdust and splinters must not be removed while the machine is running.
Only plug-in when machine is switched o.
Never reach into the danger area of the plane when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and separating.
Immediately switch o the machine in case of considerable vibrations or
if other malfunctions occur. Check the machine in order to nd out the
cause.
Always use and store the grinding disks according to the manufacturer’s
instructions.
When grinding metal, ying sparks are produced. Take care that no
persons are endangered. Because of the danger of re, no combustible
materials should be located in the vicinity (spark ight zone). Do not use
dust extraction.
Due care should be taken that no sparks or sanding dust ying from the
workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with the
machine.
The workpiece must be xed if it is not heavy enough to be steady. Never
lead the workpiece to the grinding disk with your hand.
Under extreme conditions (e.g. smooth-grinding metals with the arbour and
vulcanizedbre grinding wheel), signicant contamination can build up on
the inside of the angle grinder. For safety reasons, in such conditions the inside
should be cleaned thoroughly of metal deposits and a motor circuit-breaker
must be connected in series. If the motor circuit-breaker trips the machine
must be sent for repair.
For accessories intended to be tted with threaded hole wheel, ensure
that the thread in the wheel is long enough to accept the spindle length.
Use the safety guard from the accessories range when performing out
cutting work.
SPECIFIED CONDITIONS OF USE
The angle grinder may be used for cutting, grinding, sanding and wire
brushing a wide range of materials, such as metal or stone. If you have
any doubts, please refer to the instructions supplied by the accessory
manufacturer.
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
Inrush currents cause short-time voltage drops. Under unfavourable
power supply conditions, other equipment may be aected. If the system
impedance of the power supply is lower than 0,2 Ohm, disturbances are
unlikely to occur.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Do not let any metal parts enter the airing slots - danger of short circuit!
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order
the drawing at your local service agents or directly at: AEG Electric Tools
GmbH, Max-Eyth-Straße10, D-71364Winnenden, Germany
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Always wear goggles when using the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of European
Directive 2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with
national law, electric tools that have reached the end of
their life must be collected separately and returned to
an environmentally compatible recycling facility.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WS 2200-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WS 2200-180 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info