Manual AEG VL 5528 (page 24 of 42) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

483364

Zoom out

Zoom in

1/42

English

Assembly instructions

The device must be completely assembled before use!

While reading the text it is advisable to refer to the

„Overview of the Components“ (Illustration A).

1. Position the rear protection grid (6) in place in ac-

cordance with the recesses.

ޥ NOTE:

Please note that the borehole for the fastening

screw (3) faces downwards.

2. Turn the attachment ring (5) for the rear protection

grid (6) slightly in a clockwise direction.

3. Attach the propeller (4) to the motor shaft (7) and

press it  rmly into place.

4. Insert the front protective grille (1).

ޥ NOTE:

Ensure that the holes for the attachment screw in

the front and rear protective grille are aligned one

above the other.

5. Tighten the protective grille with the attachment

screw (3) supplied.

6. Close the attachment hooks (2).

Position

The ideal position is a non-slip,  at surface.

Wall Installation

You can also install the fan on the wall. Please remember

that there must be an electric socket close by.

Setting up the Fan (Illustration B)

1. Release the wing screw (12) on the joint.

2. Remove the stopper (11) by loosening the screw.

3. Turn the motor through 90°.

4. Turn the wing screw until it is hand-tight.

Attachment to the Wall (Illustration. C)

On the underside of the switch housing there are two

indentations. The distance between these indentations

is 36 mm.

• Drill two horizontal holes at this distance. .

CAUTION:

Please ensure beforehand that you will not be

damaging any pipes or electric wires concealed in

the wall!

• Insert rawlplugs into the holes.

• Please use two screws of size 4 x 25 mm. Allow the

screws to protrude 10 – 12 mm out of the wall.

• Suspend the switch housing by the screws. Check

that it is  rmly held in place.

Putting into Service

Electrical Connection

1. Before inserting the plug into the socket. Make sure

that the mains voltage to be used matches that of

the device. You can  nd this information on the

nameplate.

2. Connect the device to a duly installed 230V/50Hz

protective contact socket.

Use

Basic Settings

Set the blower inclination angle before starting the

device.

• In order to do this, release the wing screw (12) and

move the fan to the desired position.

• Retighten the wing screw by hand.

ޥ NOTE:

The stopper prevents the fan from falling over.

Operation

Use the pushbutton switches on the front to select the

speed:

1 = slow, 2 = fast.

Shift to „0“ to switch o the device.

Blower Direction/Oscillation

You can choose from the two following options:

1. Turn the device carefully with by hand by holding the

fan on the sides and turning it either to the left or to

the right until the limit stop

CAUTION: do not exceed this limit.

The device must have been switched o before. The

setting knob must be pulled out.

2. Select the automatic swinging direction by pressing

in the knob. The device swings automatically within

a range of 90°. This function is active only when the

fan is on. To deactivate the function pull out the set-

ting knob.

Cleaning

WARNING:

• Always remove the mains plug before cleaning the

device.

• If you need to remove the safety guard: Always

switch the device o and remove the mains plug.

• Under no circumstances should you immerse the

device in water for cleaning purposes. Otherwise

this might result in an electric shock or  re.

05-VL 5528 AEG neu.indd 2405-VL 5528 AEG neu.indd 24 02.12.2008 9:53:50 Uhr02.12.2008 9:53:50 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG VL 5528 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG VL 5528 Manual

Product: